driver side bronco.jpg 676 hits | 104.7 KB | Posted: 10/11/06 Her she is before the 3" body Lift. These are 33" tires.
mount2.jpg 608 hits | 63.71 KB | Posted: 11/3/06 when i ordered the poly body mounts i got the front core support not all the bushings i needed, but ...
lift3.jpg 585 hits | 98.47 KB | Posted: 11/3/06 Here is the PA lift as i got it from 4wheelcustoms. thanks again Chris.
mount in box.jpg 603 hits | 57.55 KB | Posted: 11/3/06 This is both front core support poly bushings and washers and sleaves. it was $26 not bad. too bad i...
lift2.jpg 639 hits | 86.16 KB | Posted: 10/11/06 This is a look in the box of the PA-3" body lift
lift.jpg 652 hits | 80.37 KB | Posted: 10/11/06 Here are the 3" body lift parts out of the box.
mounts old.jpg 635 hits | 145.38 KB | Posted: 10/11/06 I hit all the body mount bolts with PB Blaster for 2 week prior to installing the lift. the bolts ca...
oldnewbodylift.jpg 736 hits | 115.97 KB | Posted: 10/11/06 Here are the old and new Body mounts. the old rubber were soft and worn down.
new lift and mounts.jpg 741 hits | 106.45 KB | Posted: 11/3/06 Here are the old body mount shells. i cleaned and painted them to stop the rusting.. the poly mounts...
lift poly.jpg 827 hits | 101.21 KB | Posted: 10/11/06 I tossed the rubber bushings and cleaned and painted the shels. not seen i cut the nut off the botto...
mounts lift hardware.jpg 656 hits | 91.55 KB | Posted: 10/11/06 Here is all the hardware. ready to reinstall.
driverside.jpg 681 hits | 84.41 KB | Posted: 11/3/06 Here is the drivers side before the lift was installed.
Front body mount.jpg 661 hits | 80.68 KB | Posted: 12/3/06 This is the stock front Body mount before the 3" body lift and poly mount gets installed.
rear wheel.jpg 651 hits | 89.58 KB | Posted: 10/11/06 After all the bolts were out and the shells split apart. I started to jack the body up. (Look for wi...
driver side frontwheel.jpg 710 hits | 92.66 KB | Posted: 10/11/06 Here is the front blocked up. the raditor support mount is different than all the other mounts. it b...
poly and lift.jpg 805 hits | 83.98 KB | Posted: 10/11/06 here is how they go together. when doing the lift this way i did not lock tite the bolts till the ot...
lift and polymount.jpg 687 hits | 43.48 KB | Posted: 10/11/06 you can see the whole space is 4 1/2" space after the poly body mounts and body lift kit.
driver side rear.jpg 649 hits | 86.38 KB | Posted: 10/11/06 Here is alook from a few feet back. body mount and lift installed. Oh yea my two sons that are part ...
driverside front.jpg 702 hits | 79.12 KB | Posted: 10/11/06 Here is a shot with the driverside front. remember to replace all shims in the correct location. the...
driverside and kids.jpg 711 hits | 104.01 KB | Posted: 10/11/06 I planed this to goe over 2 days. saturday for the drivers side and sunday for the pass side. i want...
driverside done.jpg 885 hits | 95.17 KB | Posted: 10/11/06 here is a look from the front with only the driver side completed.
Half way done.jpg 770 hits | 80.04 KB | Posted: 10/11/06 Here is the rear end with the driverside done (my new to me 35" thornturds in the back).
driverside front2.jpg 778 hits | 100.35 KB | Posted: 10/11/06 just looks strange with 1/2 way done.
pass side lift done.jpg 1012 hits | 102.69 KB | Posted: 10/11/06 the same steps were taken on the pass side.and here is a side shot with it completly locktited and t...
rear lift done.jpg 697 hits | 88.97 KB | Posted: 10/11/06 Here is a shot from the rear with both sides done.
lift completed.jpg 687 hits | 82.73 KB | Posted: 10/11/06 Here is the front all completed.
passidefrom frontdoor.jpg 777 hits | 97.15 KB | Posted: 11/3/06 Here Jezebel is out on the street after the new 3" body lift.
newbumpersand lift.jpg 732 hits | 81.54 KB | Posted: 10/11/06 This was taken a short time later. (the bumpers were not done at the body lift time) this is out on ...
front measure.jpg 650 hits | 71.23 KB | Posted: 11/3/06 Here is the front after the body lift.
rear-measure.jpg 645 hits | 58.01 KB | Posted: 10/11/06 Here is the heigth after the body mount and 3" lift kit were installed.
broncobackcorner.jpg 624 hits | 81.48 KB | Posted: 11/3/06 Here is a view from the drivers side rear corner.
backcorner.jpg 657 hits | 90 KB | Posted: 12/3/06 here is a second look at the back corner
bedliner1.jpg 684 hits | 85.65 KB | Posted: 10/11/06 I wanted to cover the gap left but the lift so i used a stock ford truckbed liner (free from Matt)
bedliner.jpg 613 hits | 47.03 KB | Posted: 11/3/06 This was a standard bed bed liner. here is the bottom.
bedliner5.jpg 591 hits | 91.92 KB | Posted: 10/11/06 I sliced out the bottom.
bedliner7.jpg 625 hits | 95.76 KB | Posted: 10/11/06 the floo is out now.
bedliner2.jpg 632 hits | 89.11 KB | Posted: 10/11/06 I used a dramil and sliced the bed up.
bedliner6.jpg 603 hits | 84 KB | Posted: 10/11/06 Here is the floor. I decided to make a liner for the bronco..
bedliner4.jpg 587 hits | 68.42 KB | Posted: 11/3/06 Here is the rear bed liner with the rear seat flipped up.
bedliner3.jpg 623 hits | 76.45 KB | Posted: 10/11/06 The floor portion i used as a bed liner in the back of the bronco. Istopped the rear seat from bounc...
3" Body Lift
