michael collins > 1983 Ford Bronco > open folder NP 208

After the body lift i eather had to cut the floor of redisign the shifter. i did not like the locati...
trasfer.jpg
650 hits | 92.02 KB | Posted: 10/11/06
After the body lift i eather had to cut the floor of redisign the shifter. i did not like the locati...
This was round 1 with the shifter. I cut and added a 3" spacer.
shifter22.jpg
601 hits | 98.24 KB | Posted: 10/11/06
This was round 1 with the shifter. I cut and added a 3" spacer.
a coat of paint and it was looking good.
222.jpg
577 hits | 95.49 KB | Posted: 10/11/06
a coat of paint and it was looking good.
Here it is all installed and working fine.
np208shifter.jpg
615 hits | 93.72 KB | Posted: 10/11/06
Here it is all installed and working fine.
Here is another shot. i was proud of the way it turned out.
shifterinstalled.jpg
622 hits | 91.2 KB | Posted: 10/11/06
Here is another shot. i was proud of the way it turned out.
Well i was showing a friend how good a job i did and i grabbed the transfere case shifter and off it...
shifter-fixed.jpg
595 hits | 71.33 KB | Posted: 10/11/06
Well i was showing a friend how good a job i did and i grabbed the transfere case shifter and off it...
I got a new stronger rear drive shaft and this new shaft required a flang to install it not the yoke...
transferyoke.jpg
626 hits | 77.61 KB | Posted: 11/1/06
I got a new stronger rear drive shaft and this new shaft required a flang to install it not the yoke...
here is the side view of the yoke.
transferyoke2.jpg
640 hits | 70.72 KB | Posted: 11/1/06
here is the side view of the yoke.
here is the side view. i wanted to get the size so i could get the correct u joints.
transferyoke3.jpg
626 hits | 75.88 KB | Posted: 11/1/06
here is the side view. i wanted to get the size so i could get the correct u joints.
Here is the output shaft size.
transferyoke4.jpg
617 hits | 68.46 KB | Posted: 11/1/06
Here is the output shaft size.
The cv joint gets bolted to this to the transferecase.
transferyoke5.jpg
612 hits | 55.81 KB | Posted: 11/1/06
The cv joint gets bolted to this to the transferecase.
this is the rear output shaft. i got a new seal and replaced it at this time.
transfer.jpg
600 hits | 80.68 KB | Posted: 11/1/06
this is the rear output shaft. i got a new seal and replaced it at this time.
here is a different view of the case. man is it dirty.
transfer2.jpg
608 hits | 86.66 KB | Posted: 11/1/06
here is a different view of the case. man is it dirty.
Here is the new flang ready to get installed.
new shaft.jpg
631 hits | 93.58 KB | Posted: 11/1/06
Here is the new flang ready to get installed.
Here is the output shaft for the NP208. it is 32 spline shaft. this was just after i removed the yok...
np208 output.jpg
592 hits | 94.33 KB | Posted: 11/6/06
Here is the output shaft for the NP208. it is 32 spline shaft. this was just after i removed the yok...
They redesigned the seal. here is the old (left) and the new seal (right)
new_old seal.jpg
595 hits | 76.06 KB | Posted: 11/6/06
They redesigned the seal. here is the old (left) and the new seal (right)
Here is the new seal at its new home.
new flangein2.jpg
618 hits | 94.56 KB | Posted: 11/6/06
Here is the new seal at its new home.
here is the new flang in its new location. this was an easy swap.
new flangein.jpg
619 hits | 112.14 KB | Posted: 11/6/06
here is the new flang in its new location. this was an easy swap.
Here is the flang all tourqued down and ready for the new drive shaft.
new flange and seal.jpg
610 hits | 101.29 KB | Posted: 11/6/06
Here is the flang all tourqued down and ready for the new drive shaft.