michael collins > 1983 Ford Bronco > open folder EEC Install

i been working on the EEC and wire harness placement. I going to try and be as close the the stock 1...
DSC00893.JPG
529 hits | 49.3 KB | Posted: 3/9/07
i been working on the EEC and wire harness placement. I going to try and be as close the the stock 1...
another before view
DSC00894.JPG
562 hits | 55.5 KB | Posted: 3/9/07
another before view
this is the space the EEC should fit in.
DSC00895.JPG
539 hits | 48.58 KB | Posted: 3/9/07
this is the space the EEC should fit in.
this is where the new harness will come thru (I hope). the wire harness on the bottom was for the Hi...
DSC00896.JPG
555 hits | 61.3 KB | Posted: 3/9/07
this is where the new harness will come thru (I hope). the wire harness on the bottom was for the Hi...
this is the end of the high alt harness.
DSC00897.JPG
538 hits | 60.05 KB | Posted: 3/9/07
this is the end of the high alt harness.
this is the motor side of the firewall where the EEC and harness will go. you can see the high alt h...
DSC00898.JPG
599 hits | 47.58 KB | Posted: 3/9/07
this is the motor side of the firewall where the EEC and harness will go. you can see the high alt h...
the 2 rusty nuts are the ebrake mount to the right of this is where the EEC will go.
DSC00899.JPG
570 hits | 68.94 KB | Posted: 3/9/07
the 2 rusty nuts are the ebrake mount to the right of this is where the EEC will go.
this is the speedo cable and firewall shot
DSC00900.JPG
512 hits | 53.55 KB | Posted: 3/9/07
this is the speedo cable and firewall shot
here is another view of the harness and EEC before shot.
DSC00901.JPG
532 hits | 54.4 KB | Posted: 3/9/07
here is another view of the harness and EEC before shot.
here is one last look at the fire wall bafor any work was done.
wireharness as it started.JPG
631 hits | 56.56 KB | Posted: 3/12/07
here is one last look at the fire wall bafor any work was done.
here is the inside where the computer and harness connectors will go.
computerinside.JPG
526 hits | 57.55 KB | Posted: 3/12/07
here is the inside where the computer and harness connectors will go.
here is the EEC pocket. there is a seam running at an angle in the back of the pocket but that will ...
computer2.JPG
608 hits | 36.75 KB | Posted: 3/12/07
here is the EEC pocket. there is a seam running at an angle in the back of the pocket but that will ...
this is the EEC mount i made a template to get the correct spacing and hole size.
computer harness.JPG
619 hits | 60.32 KB | Posted: 3/12/07
this is the EEC mount i made a template to get the correct spacing and hole size.
this was one reason i changed the front cowl as it allows alot of leaves and dirt in the cowls and r...
leaves.JPG
563 hits | 56.72 KB | Posted: 3/12/07
this was one reason i changed the front cowl as it allows alot of leaves and dirt in the cowls and r...
i vaccumed out the leaves and dirt. thius should not be an issue any more. you can see the junk.
leaves2.JPG
527 hits | 57.29 KB | Posted: 3/12/07
i vaccumed out the leaves and dirt. thius should not be an issue any more. you can see the junk.
after some measuring and carefull cutting i got the computer mount and computer installed. it looks ...
computer.JPG
628 hits | 60.26 KB | Posted: 3/12/07
after some measuring and carefull cutting i got the computer mount and computer installed. it looks ...
here is under the hood with the gasket in place. i covered the connection point to keep out dirt. lo...
computer3.JPG
615 hits | 52.01 KB | Posted: 3/12/07
here is under the hood with the gasket in place. i covered the connection point to keep out dirt. lo...