Rack Hardware.JPG
1320 hits | 62.29 KB | Posted: 7/13/03
The roof rack came from a '96 4-door Explorer, but was cut down one mounting screw. The runners are...

Rack Install.JPG
1026 hits | 41.52 KB | Posted: 7/13/03
Some of the nuts have to be spaced down or shortened because the roof is so thin.

Rack Installation.JPG
1009 hits | 77.7 KB | Posted: 7/13/03
Although silicone helps hold the nuts while screws are being installed, the first camper I did this ...

Rack Ready.JPG
1960 hits | 63.26 KB | Posted: 7/13/03
I cut the front of the tracks and installed 2 rear crossbars because they can both be (re)moved with...

Camper Colors.JPG
1232 hits | 81.53 KB | Posted: 7/13/03
This shows the difference in colors between the 2 years. The '96 is "mocha".

Camper Difference.JPG
1299 hits | 77.39 KB | Posted: 7/13/03
Besides the third brake light, shoulder belts, and color, this is another difference in Bronco campe...

Side Remove 1.JPG
1311 hits | 68.2 KB | Posted: 7/13/03

Side Remove 2.JPG
1024 hits | 65.47 KB | Posted: 7/13/03

Side Remove 3.JPG
1094 hits | 78.33 KB | Posted: 7/13/03

Trim Begin.JPG
985 hits | 75.15 KB | Posted: 7/13/03
Although I'm not using these gaskets, I replaced the trim in them. It's more difficult than changin...

Trim Corner1.JPG
814 hits | 71.79 KB | Posted: 7/13/03
It took a while to learn that the INSIDE corner is the hardest, so start there and then work the out...

Trim Strips1.JPG
734 hits | 68.47 KB | Posted: 7/13/03
Insert only the ends of the strips to start, but do both ends of each strip.

Trim Corner2.JPG
790 hits | 70.95 KB | Posted: 7/13/03
A hard plastic tool with blunt edges would have been MUCH better.

CamperPins.JPG
251 hits | 31.8 KB | Posted: 9/25/07
These spikes screw into '78-91 Bronco bedrails & are removeable to prevent injury when the top is of...

Trim Strips2.JPG
730 hits | 68.45 KB | Posted: 7/13/03
With both ends in, work toward the middle. Extra silicone helps. Silicone grease would be better.

Side Install 1.JPG
761 hits | 73.33 KB | Posted: 7/13/03

Side Install 2.JPG
753 hits | 65.76 KB | Posted: 7/13/03

Side Install 3.JPG
826 hits | 66.71 KB | Posted: 7/13/03

Side Install 4.JPG
697 hits | 57.5 KB | Posted: 7/13/03

Slider 1.JPG
913 hits | 46.1 KB | Posted: 7/13/03

Slider 2.JPG
891 hits | 69.91 KB | Posted: 7/13/03

Slider 3.JPG
831 hits | 50.82 KB | Posted: 7/13/03

Slider 4.JPG
1680 hits | 58.56 KB | Posted: 7/13/03
'83 sliders in a '96 camper shell on an '82 body with a '9? Town Car dome lamp.

CamperShellDetails.jpg
980 hits | 72.04 KB | Posted: 1/17/06
Camper Shell Details

The felt glass run is F2TZ-98422A00-A and cost $37 in 1998.

CamperShellTrim.jpg
731 hits | 59.01 KB | Posted: 1/17/06
Camper Shell Trim

1 Roof Trim Rear Moulding 517C04
2 Quarter Window Garnish Lower Front Moulding...

28CamperPin.JPG
440 hits | 74.62 KB | Posted: 3/31/06
These pins align the front of the camper shell.

29CamperHole.JPG
416 hits | 41.88 KB | Posted: 3/31/06
These bolt holes are for the integral roll bar in the camper shell. The slot between them is for th...

RollBar1.JPG
612 hits | 67.7 KB | Posted: 4/23/06
The steel roll bar inside the factory Bronco camper shell is bolted to the bedwalls. This is an '83...

RollBar2.JPG
636 hits | 84.19 KB | Posted: 4/23/06
The steel roll bar inside the factory Bronco camper shell is bolted to the bedwalls. This is an '83...

PopupIdea.JPG
742 hits | 62.46 KB | Posted: 8/10/07
Just a freaky idea I've been contemplating.

TGRun.JPG
111 hits | 36.06 KB | Posted: 5/11/08
Glass Run

Some aftermarket versions are simply a continuous strip - they lack the formed corner p...