SuperMotors SuperMotors SUPERMOTORS Search: try “orange Bronco on 35s”
Join
Hand holding a copper pipe with a brass ferrule, open engine bay in a garage behind
Home/ Registry/ Ford/ Probe/ 1993-1997/ “Baby” supermotors.net/registry/11015

“Baby”1993 Ford Probe

documented by fats 38 photos documented since 1 years documented 8 sounds ♡ Follow this build

Photos

Hand holding a copper pipe with a brass ferrule, open engine bay in a garage behind Copper fuel line with a brass nut and ferrule on a workbench, instructional text overlay Single brass nut on a wooden surface with overlay text about cutting it with a dremel Engine bay fitting with metal flange and two worm-gear hose clamps, instructional text overlay Blue adjustable fuel pressure regulator with gauge and copper bracket mounted in an engine bay Brass and copper fittings, a nut, and a bent copper pipe laid out on a wooden workbench 50 gal wood burner 1993 Ford Probe: Car center console with aftermarket head unit, three HVAC knobs, and a blue amp display 1993 Ford Probe: intermediate shaft 1993 Ford Probe: Black leather MOMO bucket seat with cracked perforated leather, mounted in a vehicle 1993 Ford Probe: Two black leather MOMO bucket seats with seatbelt inside a car interior My daughter with my mother Sandstone canyon walls with green moss and ferns, people standing on a ledge above Ford 2.5L engine wiring diagram page 25-9 with PCM connector pinouts and circuit tables Ford 2.5L engine control manual page 25-10 with C247 and C248 connector pinout tables Young girl in pink shirt wearing pink-rimmed sunglasses smiling in a living room 1993 Ford Probe: 2.7 liter KLZE Young man with short dark hair and stubble in a blue shirt reclining on a couch 1993 Ford Probe: Worm-gear hose clamps on a rubber hose under a vehicle with a wrench nearby 1993 Ford Probe: STEP 1:sand with dremel this area to reveal the power bar. 1993 Ford Probe: STEP 2: use cutting wheel to remove the power bar cut a square out. 1993 Ford Probe: STEP 3: remove cut section. usually fall out with a touch! 1993 Ford Probe: STEP 4: You need a post! what a cheap way an old spark plug use hammer to break ceramic. cut a piece off! tha… 1993 Ford Probe: STEP 5: Drill a hole in the center for the post use a size smaller than diameter of post. youll need to clean… 1993 Ford Probe: Use a plastic bond. (2 part mix) and fill the hole(this is needed to protect metal from grounding) take and f… 1993 Ford Probe: polishing in progress Engine bay with valve covers off a transverse Mazda V6 during a teardown, battery at right 1993 Ford Probe: in progress... Mazda engine bay with chrome valve cover and rags 1993 Ford Probe: wheel view of lawnmower muffer on other side of inter-cooler pipe Close-up of undercarriage exhaust and driveline components 1993 Ford Probe: bottom passanger side view notice extra weld on pipe.. made a cut in the pipe, bent it, welded space had too… Engine bay with turbo and blue cone air filter 1993 Ford Probe: huge oil cooler if water pump goes this should keep temp down a little...: ) 1993 Ford Probe: greddy installed in a nifty spot Engine bay with turbo manifold and blue cone air filter 1993 Ford Probe: oil catch can Engine bay close-up of a V6 with aftermarket intake piping

Albums · 4

How the owner organised this build. Open an album for every photo in it.

Mods and Diagrams - 1993 Ford Probe Mods and Diagrams 29 photos Poverty 12 sounds DISTY - 1993 Ford Probe DISTY 6 photos muffler wastegate - 1993 Ford Probe muffler wastegate 3 photos
See every Ford Probe in the registry The 1993-1997 Ford Probe registry

The peanut gallery

No comments yet. Be the first to add to the record.

Spotted in the wild

Seen this vehicle at a show or on the trail? Add your shot. The owner approves it onto the record.