DSCN1495.JPG
366 hits | 100.49 KB | Posted: 8/28/08
New hotness next to old 'n' busted.

DSCN1496.JPG
367 hits | 90.81 KB | Posted: 8/28/08
Showin' the raised top.

DSCN1497.JPG
348 hits | 62.03 KB | Posted: 8/28/08
Air diverter/roof support at the rear.

DSCN1498.JPG
328 hits | 74.42 KB | Posted: 8/28/08
Front roof support and air diverter.

DSCN1486.JPG
371 hits | 111.48 KB | Posted: 8/28/08
Overview of what it used to be with the new blower sitting on its throne.

DSCN1489.JPG
357 hits | 84.16 KB | Posted: 8/28/08
Inlet was designed by a friend of mine in NE off of the club boards. He buit this inlet to accept a...

DSCN1490.JPG
543 hits | 63.75 KB | Posted: 8/28/08

DSCN1491.JPG
380 hits | 59.1 KB | Posted: 8/28/08

DSCN1492.JPG
329 hits | 98.25 KB | Posted: 8/28/08
3" outlet and inlet should be good enough to feed from the 85mm t-body.

DSCN1493.JPG
348 hits | 91.58 KB | Posted: 8/28/08
Its a bit short after raising the manifold. I think I can use a longer hose to make it fit.

DSCN1494.JPG
366 hits | 102.02 KB | Posted: 8/28/08
3" inlet (manifold inlet that is) from the intercooler.

DSCN1506.JPG
330 hits | 112.83 KB | Posted: 9/9/08
Well....could not afford to finish the 6 shooter at this point. Grabbed the 351 out of the Bronco, ...

DSCN1507.JPG
287 hits | 84.08 KB | Posted: 9/9/08
There are some things that I just do not want to change. The cam is itty bitty and was put in the 3...

DSCN1509.JPG
347 hits | 77.68 KB | Posted: 9/9/08
'Nother cam pic.

Chris

DSCN1511.JPG
345 hits | 86.86 KB | Posted: 9/9/08
If you look, it has a heated steel core/lobes and a cast gear/front journal.

DSCN1513.JPG
355 hits | 76.77 KB | Posted: 9/9/08
You can see the casting flash on the top edge.

DSCN1514.JPG
316 hits | 97.36 KB | Posted: 9/9/08
Drill an itty bitty hole in the lifter galley oil passage to the right of the cam. This will lube t...

DSCN1515.JPG
305 hits | 106.34 KB | Posted: 9/9/08
I think it is .030" but check with others before you do it.

DSCN1516.JPG
323 hits | 59.87 KB | Posted: 9/9/08

DSCN1570.JPG
344 hits | 90.69 KB | Posted: 9/12/08

DSCN1571.JPG
324 hits | 110.05 KB | Posted: 9/12/08

DSCN1572.JPG
299 hits | 100.56 KB | Posted: 9/12/08

DSCN1573.JPG
331 hits | 78.63 KB | Posted: 9/12/08

DSCN1580.JPG
336 hits | 117.78 KB | Posted: 9/12/08

DSCN1581.JPG
347 hits | 98.63 KB | Posted: 9/12/08

DSCN1582.JPG
319 hits | 69.41 KB | Posted: 9/12/08

DSCN1728.JPG
349 hits | 90.98 KB | Posted: 11/10/08
D.S.S. Main support system and windage tray bolted to the bottom end.

DSCN1729.JPG
324 hits | 67.61 KB | Posted: 11/10/08
Nice work on it.

DSCN1730.JPG
324 hits | 76.12 KB | Posted: 11/10/08
Eagle H beam rods. Got a killer deal on 'em.

DSCN1731.JPG
310 hits | 93.62 KB | Posted: 11/10/08

DSCN1946.JPG
292 hits | 95.47 KB | Posted: 3/22/09

DSCN1947.JPG
285 hits | 101.33 KB | Posted: 3/22/09

DSCN1948.JPG
282 hits | 77.33 KB | Posted: 3/22/09

DSCN1949.JPG
291 hits | 68.62 KB | Posted: 3/22/09

DSCN1950.JPG
333 hits | 95.86 KB | Posted: 3/22/09

DSCN1951.JPG
334 hits | 46.16 KB | Posted: 3/22/09

DSCN1953.JPG
304 hits | 61.08 KB | Posted: 3/22/09

DSCN1954.JPG
282 hits | 47.97 KB | Posted: 4/3/09

DSCN1955.JPG
313 hits | 50.8 KB | Posted: 4/3/09

DSCN1956.JPG
331 hits | 63.41 KB | Posted: 4/3/09

DSCN1957.JPG
279 hits | 44.48 KB | Posted: 4/3/09

DSCN1958.JPG
304 hits | 63.99 KB | Posted: 4/3/09

DSCN2070.JPG
334 hits | 86.99 KB | Posted: 4/17/09

DSCN2071.JPG
274 hits | 85.69 KB | Posted: 4/17/09

DSCN2072.JPG
269 hits | 92.8 KB | Posted: 4/17/09

DSCN2073.JPG
289 hits | 56.68 KB | Posted: 4/17/09

DSCN2071.JPG
310 hits | 85.69 KB | Posted: 4/17/09

DSCN2223.JPG
355 hits | 98.81 KB | Posted: 6/9/09

DSCN2222.JPG
317 hits | 88.18 KB | Posted: 6/9/09

Image0117[1].jpg
213 hits | 51.85 KB | Posted: 11/27/11

Image0118[1].jpg
194 hits | 50.37 KB | Posted: 11/27/11

Image0119[1].jpg
190 hits | 50.07 KB | Posted: 11/27/11

Image0120[1].jpg
210 hits | 59.67 KB | Posted: 11/27/11