SuperMotors SuperMotors SUPERMOTORS Search: try “orange Bronco on 35s”
Join
Home/ Registry/ Ford/ Bronco/ 1987-1991/ “Eddie Bauer”/ Throttle Position Sensor supermotors.net/registry/20487/78381

Album section

Throttle Position Sensor

From 1990 Ford Bronco “Eddie Bauer”, documented by SeattleFSB.

43 photos
← Back to this vehicle
1990 Ford Bronco - OBD1 code reader connected to a vehicle's engine bay, displaying a temperature reading. 1990 Ford Bronco - A hand holds multimeter probes connected to engine components, displaying a reading of 4.78V DC. 1990 Ford Bronco - Testing resistance with a multimeter in an automotive engine bay. 1990 Ford Bronco - A multimeter reads 3.75 ohms while testing a throttle position sensor connector. 1990 Ford Bronco - Hand near a black round distributor cap on an engine surrounded by blue plug wires and a red MSD-labeled part. 1990 Ford Bronco - Close-up of an engine intake area showing a copper throttle linkage rod, return spring, brackets and blue spark plug wires. 1990 Ford Bronco - A screwdriver is used to adjust the linkage on a vehicle's throttle body, connected by an orange cable. 1990 Ford Bronco - Close-up of a throttle linkage mechanism, showing the cable and associated hardware. 1990 Ford Bronco - This image shows a throttle body and its associated sensor and linkage mechanism. 1990 Ford Bronco - A hand disconnects a throttle position sensor connector from a red component labeled 'ESD'. 1990 Ford Bronco - Close-up of a throttle position sensor connector being held, showing internal wiring. 1990 Ford Bronco - Close-up of a brass-bodied coolant temperature sensor threaded into an aluminum housing with its gray two-pin connector plugged in, plus a… 1990 Ford Bronco - Hand holding an aluminum dual-bore throttle body showing two throttle bores, linkage and sensor on pavement. 1990 Ford Bronco - Throttle body and two cans of CRC cleaner are laid out on a workbench for maintenance. 1990 Ford Bronco - This is a throttle body assembly, likely from an older vehicle, with visible text on a component cap. 1990 Ford Bronco - A throttle position sensor potentiometer, part number CX-1228 E7TZ-9B989-D, is shown in its packaging. 1990 Ford Bronco - Aluminum throttle body or EGR housing held over a ruler, with detached two-wire connector and pigtail. 1990 Ford Bronco - Comparison of a new and used throttle position sensor, showing wear on the older part. 1990 Ford Bronco - Comparison of two throttle position sensor components, highlighting the TPS shim ring. 1990 Ford Bronco - Disassembled throttle position sensor components with a gasket are laid out on a textured white surface. 1990 Ford Bronco - The throttle position sensor assembly is shown disassembled, revealing internal components like a bearing and shaft. 1990 Ford Bronco - Close-up of a throttle body showing the flat-blade throttle shaft end (top) and the matching slotted receiver of a black plastic throttle p… 1990 Ford Bronco - A BBK Power-Plus twin 65mm aluminum throttle body sitting on a shop towel over a wood workbench, with a black wiring harness (orange/green… 1990 Ford Bronco - Close-up view of engine components, including intake manifold and ignition system parts. 1990 Ford Bronco - Fel-Pro throttle body gasket for Ford 5.0L and 5.8L engines from 1986-1995. 1990 Ford Bronco - A multimeter displays a voltage reading while being used to test engine components. 1990 Ford Bronco - Engine bay features a K&N air intake system with blue silicone couplers and blue vacuum lines. 1990 Ford Bronco - A throttle position sensor wiring harness with frayed wires and connectors is shown on a white towel. 1990 Ford Bronco - Close-up of a hand holding a disconnected wiring harness in an engine bay, revealing exposed wires and a visible part number. 1990 Ford Bronco - A hand holds multimeter probes to wires in an engine bay, displaying a voltage reading. 1990 Ford Bronco - Testing engine wiring with a multimeter, showing a DC voltage reading of 1.758. 1990 Ford Bronco - A digital multimeter is used to measure voltage within a vehicle's engine bay, showing a reading of 2.62 volts. 1990 Ford Bronco - A throttle position sensor and a drill bit are shown on a concrete surface with dry leaves. 1990 Ford Bronco - Multimeter reading .983 volts in an engine bay with an MSD ignition component. 1990 Ford Bronco - A multimeter reads 4.61 volts while connected to various engine parts. 1990 Ford Bronco - A multimeter reads 0.98 volts while connected to engine components, likely for diagnostics. 1990 Ford Bronco - Digital multimeter showing 46 used to test an engine; blue spark plug wires, alternator and throttle body visible. 1990 Ford Bronco - A Ford OBD I code reader, compatible with domestic vehicles from 1981 to 1995, is shown in a hand. 1990 Ford Bronco - The engine bay features a K&N air intake system with blue accents and visible hoses. 1990 Ford Bronco - Custom wiring harness with alligator clips, likely for testing automotive electrical components. 1990 Ford Bronco - Close-up of a throttle position sensor connector, showing internal contacts and a green seal. 1990 Ford Bronco - Schematic of a throttle position sensor potentiometer showing the rotating wiper, resistive element and VREF/TP SIG/SIG RTN leads. 1990 Ford Bronco - A close-up view of a throttle position sensor, a critical component for engine management.