Steve83 > 1983 Ford Bronco > open folder Lock Cylinder

Door & Ignition Lock Cylinder ReplacementsIF THE IMAGE IS TOO SMALL, click it.For any '80-96/7 F-...
Match01a.jpg
371 hits | 92.58 KB | Posted: 3/16/24
Door & Ignition Lock Cylinder Replacements
IF THE IMAGE IS TOO SMALL, click it.

For any '80-96/7 F-...
Instruction Sheet for Ford (StratTech) 8-cut ignition lock cylinder assembly IF THE IMAGE IS TOO SM...
FordIS.jpg
305 hits | 44.85 KB | Posted: 3/16/24
Instruction Sheet for Ford (StratTech) 8-cut ignition lock cylinder assembly
IF THE IMAGE IS TOO SM...
Door Lock Cylinder Replacement IF THE IMAGE IS TOO SMALL, click it. In addition to removing all ...
DoorCylSwap.jpg
274 hits | 44.59 KB | Posted: 3/16/24
Door Lock Cylinder Replacement
IF THE IMAGE IS TOO SMALL, click it.

In addition to removing all ...
Key-In Contact Repair[url=https://www.supermotors.net/registry/media/1092884][img]https://www.supe...
BuzzKey.JPG
3432 hits | 139.11 KB | Posted: 1/4/15
Key-In Contact Repair

[url=https://www.supermotors.net/registry/media/1092884][img]https://www.supe...
This original '93 collar (using the 10-cut key) is very loose, causing several annoying problems. W...
Collar01.JPG
1570 hits | 114.15 KB | Posted: 9/3/14
This original '93 collar (using the 10-cut key) is very loose, causing several annoying problems. W...
If the key-in switch is damaged, it can be discarded. This one is OK, so I removed it carefully.[...
Collar02.JPG
1106 hits | 114.98 KB | Posted: 9/3/14
If the key-in switch is damaged, it can be discarded. This one is OK, so I removed it carefully.

[...
The cylinder must be rotated back to OFF before rotating forward past START to disassemble it from i...
Collar03.JPG
1002 hits | 103.36 KB | Posted: 9/3/14
The cylinder must be rotated back to OFF before rotating forward past START to disassemble it from i...
As the cylinder passes START, the cam on the end will disengage from the mating cam in the housing, ...
Collar04.JPG
979 hits | 109.05 KB | Posted: 9/3/14
As the cylinder passes START, the cam on the end will disengage from the mating cam in the housing, ...
Note the orientation of the detent ring as it falls off. Don't lose the brass detent springs & pins...
Collar05.JPG
936 hits | 107.69 KB | Posted: 9/3/14
Note the orientation of the detent ring as it falls off. Don't lose the brass detent springs & pins...
Inspect all the working parts of the cylinder. If it's damaged or worn, don't waste your time tryin...
Collar06.JPG
992 hits | 110.14 KB | Posted: 9/3/14
Inspect all the working parts of the cylinder. If it's damaged or worn, don't waste your time tryin...
Use brake cleaner liberally (in a ventilated area where the overspray & drips won't damage anything)...
Collar07.JPG
881 hits | 107.37 KB | Posted: 9/3/14
Use brake cleaner liberally (in a ventilated area where the overspray & drips won't damage anything)...
Insert the key, align the collar perfectly, mark the collar to the cylinder, and remove the key whil...
Collar08.JPG
935 hits | 102.37 KB | Posted: 9/3/14
Insert the key, align the collar perfectly, mark the collar to the cylinder, and remove the key whil...
Apply glue to a small area and allow it to dry while holding alignment. Recheck, and if necessary, ...
Collar09.JPG
898 hits | 105.15 KB | Posted: 9/3/14
Apply glue to a small area and allow it to dry while holding alignment. Recheck, and if necessary, ...
Once they're glued together in one spot, fill the gap between the collar & cylinder, allowing the gl...
Collar10.JPG
896 hits | 93.88 KB | Posted: 9/3/14
Once they're glued together in one spot, fill the gap between the collar & cylinder, allowing the gl...
Once the glue is thoroughly dry, and you're satisfied with the alignment, apply light oil to the cyl...
Collar11.JPG
852 hits | 106.55 KB | Posted: 9/3/14
Once the glue is thoroughly dry, and you're satisfied with the alignment, apply light oil to the cyl...
Insert the cylinder back into the housing, aligning the cams at the inner end, then rotate the cylin...
Collar13.JPG
989 hits | 105.48 KB | Posted: 9/3/14
Insert the cylinder back into the housing, aligning the cams at the inner end, then rotate the cylin...