1995 Ford Bronco
| Owner: |
Steve83 (All of this user's registries on SuperMotors) |
| From: |
Memphis, TN, U.S.A. (Other registries in TN) |
| Year, Make, & Model: |
1995 Ford Bronco (Other Ford Broncos) |
| Avatar: |
 |
| Clubs: |
SuperFord.org (Other vehicles in this club)
|
| Nickname: |
The Charm NOT MINE |
| Mileage: |
170000 |
| Engine: |
5.8L EEC-IV MAF DPFE VMV re-sealed & painted Oct.2018, JBG HD poly mounts |
| Drivetrain: |
E4OD, BW1356 ESOF, Ford 8.8" 3.55 LS, D44IFS 3.54 open |
| Notes: |
Bought (by a local friend) used as a replacement for a totalled white '96 EB Bronco. Some parts were swapped from the '96 (fuel pump, trans mount, chairs, a door panel, outside HVAC box, battery hold-down, hood stop), and many others were replaced with new (Energy black body mounts, engine mounts, suspension bushings, timing cover gasket, pan gasket, EGR pipe, lower radiator hoses, battery terminals, ). Magnefine PS & ATF filters were added. The driver's inside door handle, window motor, & swingaway handle were repaired, and the RHS cowl drain was emptied. |
| Last Updated: |
3/8/2024 |
| Hits: |
5675 |
 HarnessWear95B.jpg
25 hits | 82.53 KB | Posted: 3/8/24
Harness Repair
IF THE IMAGE IS TOO SMALL, click it.
The overhead console, speedometer, and a few other things became intermittent, and the fault was eventually traced to the engine bay wiring harness being loose over the LHF wheelwell, which was ...
 DistPin.jpg
30 hits | 94.82 KB | Posted: 3/8/24
Distributor Gear Pin
IF THE IMAGE IS TOO SMALL, click it.
After a few days of intermittent rough-running, the cheapo chy-neez distributor pin was found sheared. Somehow, the engine kept running well-enough for the truck to be driven. Ford gears a...
 20181017_133836.jpg
380 hits | 56.22 KB | Posted: 11/16/18
Copper-Coat gasket adhesive 60697
DupliColor New Ford Gray DE1611
Fel-Pro Timing Cover Gasket Set 45449
Fel-Pro Water Pump Gasket 35380
IF THE IMAGE IS TOO SMALL, click it.
 20181016_165949.jpg
319 hits | 97.53 KB | Posted: 11/16/18
Energy black polyurethane Bronco body mounts & shock bushings
JBG HD smallblock V8 engine mounts w/polyurethane bushings
 20181010_093738.jpg
287 hits | 56.37 KB | Posted: 11/16/18
Belt 6PK2590
Balancer pulley F2UA-6312-CA
 20181010_093533.jpg
260 hits | 71.21 KB | Posted: 11/16/18
OE A/C compressor label was not legible
IF THE IMAGE IS TOO SMALL, click it.
FS10...
...COMPRESSOR F4TH-19D320...
 20181010_095815.jpg
285 hits | 65.16 KB | Posted: 11/16/18
Cheap aftermarket ICM
F100914
 20181009_182852.jpg
304 hits | 54.35 KB | Posted: 11/16/18
The last 4 digits of the DOT number indicate these tires were made the 07th week of 2012 (~6.7 years ago)
For pics of the repairs to the truck, go to this album.
 20181011_143019.jpg
541 hits | 82.14 KB | Posted: 11/16/18
OE '95 Bronco E4OD rear driveshaft
F0TA-4602-ZA
915841-1008
36149 KC Prod 06-21-95
 20181010_164204.jpg
1379 hits | 85.84 KB | Posted: 11/14/18
The Bronco was delivered on a rollback due to stalling in traffic & not restarting. But it drove off the wrecker, and I drove it around without any apparent problem. So after cleaning out the FDM & swapping in the '96 pump (the '95 tank plate had t...
 20181009_134056.jpg
1111 hits | 87.2 KB | Posted: 11/14/18
 20181010_095650.jpg
732 hits | 93.13 KB | Posted: 11/16/18
OE 4WABS HCU
IF THE IMAGE IS TOO SMALL, click it.
Ford F3TA-BE 5159
Ate 10 0202-0183 4
1300501830005902
 20181018_162302.jpg
673 hits | 94.83 KB | Posted: 11/15/18
I decided to re-hang this box before putting the engine back since the evaporator is a tight fit past the plenum. The original evaporator insulation was mostly-intact, but decaying, and wet. So I traced it onto this Aluminized bubble sheet, which sh...
 20181022_162438.jpg
631 hits | 77.53 KB | Posted: 11/15/18
The lower radiator hose is routed so it doesn't rest against the PS box, and its split loom is positioned to protect it, if it ever does touch.
[url=https://www.supermotors.net/vehicles/registry/media/1142380][img]https://www.supermotors.net/getfile...
 20181014_151203.jpg
630 hits | 99.35 KB | Posted: 11/15/18
I really should have pulled the hood first, but without the water pump and with the front tires flat, it came out pretty easily.
 20181016_202943.jpg
602 hits | 104.99 KB | Posted: 11/15/18
The JBG engine mounts arrived assembled, but unpainted. So they got engine paint, like the timing cover bolts, and HB bolt & washer.
[url=...
 20181017_172050.jpg
580 hits | 99.2 KB | Posted: 11/15/18
New gaskets for the timing cover, water pump, & oil pan
The new EGR pipe is on the way, but ...
 20181010_164026.jpg
542 hits | 96.15 KB | Posted: 11/16/18
'95 5.8L Bronco Fuel Pump made 1994-09-07, 2nd shift
Ford F4TU-9350-A1A
125 Liters per hour @ 310KPa
Maintenance & Modification Logs
This user hasn't added any log entries, yet.
|
|
