Blueprints: Ford Bronco 1992-1996

Technical Reference

Member-uploaded diagrams & documents for this generation. AI-classified; community-verified where badged.

Blueprints

• Brake Booster to Master Cylinder Adapter Plate Blueprint - Ford Bronco Swap
  This document is a dimensioned mechanical blueprint (CAD drawing) of a circular adapter plate, uploaded as "Booster2MCplate.jpg", apparently a plate for mating a brake booster to a master cylinder. The plate has an…
• Shop Foundation Slab Plan Blueprint - 60' x 52' Layout with Section Details S-2
  This document is a structural foundation/slab plan blueprint, apparently for a shop building (upload filename: 'shop foundation drawing clip j.jpg'), not an automotive reference. The plan shows a roughly 60'-3 1/2"…
• Shop Foundation Plan Drawing - Grid C3-C21, S-2 Section Callouts & Dimensions
  This scan is a portion of an architectural/structural foundation plan drawing (site-labeled as part of a 'shop foundation drawing' set) that was uploaded to a 1995 Ford Bronco gallery, but it contains no automotive…
• 12" Single Ported Subwoofer Box Cut Sheet & Blueprint (HDS/HDC 12" Subs)
  This document is a builder's blueprint/cut sheet for a single 12-inch ported subwoofer enclosure. It includes two rendered diagrams: a 3D exterior view of the box showing the round woofer cutout and reference…
• 1994 Ford Bronco Custom Sub Box Top View Blueprint - Dimensions & Layout
  This document is a dimensioned CAD-style line drawing, apparently a top view of a custom subwoofer enclosure (filename "Sub Box Top 2.jpg") for a 1994 Ford Bronco audio installation. The drawing shows the outline of…
• Subwoofer Box Front Baffle Blueprint: 25.25x14 in Panel, 11.25/12.88 in Cutouts
  This document is a CAD-style dimensioned blueprint (two views) for the front panel of a custom subwoofer enclosure, uploaded as part of a car-audio build set for a 1994 Ford Bronco. The upper drawing shows a…
• Crankshaft Spacer/Balancer Shim Blueprint MC 98264A225 - Dimensions & Specs
  This document is a mechanical engineering blueprint (sheet 4 of 4) produced by Amesbury Statesville West of Statesville, NC 28625, titled "CLOCKING" (drawing number "271 clocking"), drawn by GMS on 2/5/14. It details a…
• Ford Bronco SD Seat Adapter Passenger Side Brackets Blueprint - Dimensions
  This blueprint-style drawing, titled "Passenger Side Brackets," provides fabrication dimensions for two custom seat adapter brackets, a Front Bracket and a Rear Bracket, intended for mounting a Super Duty (SD) seat…
• Super Duty Seat Adaptor Plate Blueprint v2 - Ford Bronco Seat Swap Dimensions
  This document is a fabrication blueprint (dimensioned drawing) for a seat adaptor plate, uploaded as "SD Seat Adaptor plate version 2" to accompany a Super Duty seat swap into a 1994 Ford Bronco. The drawing shows a…
• Blueprint of the 1992 Ford Bronco underbody frame with top and side view measurements, measuring point designations and a tightening specifications table.
• Ford Bronco Super Duty Seat Adapter Top Plate Blueprint - Dimensions & Hole Layout
  This document is a dimensioned mechanical blueprint (CAD drawing) for a flat plate, uploaded as "SD Seat Adaptor Top Plate", the top plate of a seat adapter bracket intended to mount a Super Duty seat into a 1994 Ford…
• Ford Bronco SD Seat Adaptor Side Plate Blueprint - Dimensions & Angle
  This document is a simple dimensioned CAD-style blueprint of a flat side plate, uploaded as "SD Seat Adaptor Side Plate" in an album relating to adapting a Super Duty power seat into a 1994 Ford Bronco. The drawing…
• Spicer End Yoke Dimension Diagram - BS/CV/HR/UB Style (S, Q, R, E Callouts)
  This document is a technical line drawing (blueprint-style illustration) of a Spicer driveshaft end yoke, labeled "BS/ CV/ HR/ UB Style." The drawing shows a side/cross-section view of the yoke with four dimension…
• Axle Tube Perch Blueprint - Fits 3 3/8" or 3 1/2" Tube, Dimensioned Drawing
  This document is a dimensioned CAD blueprint (three views: side profile, top view, and a shaded 3D isometric render) of an axle spring/link perch or tube saddle designed to fit large-diameter axle tubes. The saddle…
• 1995 Ford Bronco Outer Ring Blueprint - Dimensions & Bolt Hole Circle Diagram
  This document is a hand-drawn dimensional blueprint (diagram) of an "Outer ring," apparently one part of a two-piece ring set (a companion file, Inner_ring.jpg, exists in the same album). The drawing shows two…
• DIY Beadlock Inner Ring Blueprint - Dimensions & Bolt Hole Circle Specs
  This document is a hand-made blueprint/diagram (titled "Inner ring") showing dimensions for fabricating an inner beadlock-style ring for a wheel. It depicts two concentric circles representing the ring, with labeled…
• V-Nose Cargo Trailer Blueprint - Road Side Elevation with Dimensions
  This document is a dimensioned CAD line drawing (blueprint) showing the road-side elevation of a small V-nose cargo/utility trailer. The drawing depicts the trailer body in side profile with a single-axle wheel well…
• V-Nose Enclosed Trailer Conversion Blueprint - Plan View Floor Layout
  This document is a CAD-style plan (top-down) view blueprint of a V-nose enclosed trailer, apparently a custom camping/toy-hauler or ice-house style conversion. The drawing shows the trailer's interior layout and…
• Enclosed V-Nose Trailer Fabrication Plan View - Doors, Windows & Ramp Layout
  This document is a fabrication plan-view (top-down) blueprint of an enclosed V-nose trailer, showing the layout of doors, windows, and structural features as seen from above. The drawing is a line diagram with labeled…
• Custom 12' Cargo/Camper Trailer Blueprint - Curb Side View with Dimensions
  This document is a dimensioned blueprint titled by its filename as a curb-side elevation view of a custom cargo/camper trailer. The drawing shows a trailer body 12'-0" long and 6'-0" tall, with an additional 3'-0"…
• DIY Camper/Cargo Trailer Blueprint - 12' Side Elevation with Door & Window Layout
  This document is a CAD-style side elevation blueprint of a small single-axle cargo/camper trailer, uploaded to a 1996 Ford Bronco gallery as one page of a multi-page plan set (curb side, road side, plan, and…
• Trailer Road Side View Blueprint - 10' Body, 3' V-Nose, Door & Window Dimensions
  This document is a dimensioned CAD-style blueprint labeled as the "road side view" of a small trailer (part of a multi-page set including angle, curb side, plan, and fabrication plan views). The elevation drawing shows…
• DIY Beadlock Ring Blueprint - Inner & Outer 1/4" Steel Rings, 30-Hole Pattern
  This is a CAD blueprint titled "BEADLOCKS" showing two circular ring components used to build beadlock wheels: an INNER BEADLOCK and an OUTER BEADLOCK, each requiring (4) pieces made from 1/4" steel. Both rings share…
• 1996 Ford Bronco/F-150 Frame Dimensions - Underbody Misalignment Check Diagram
  This document is a Ford factory-style frame/underbody misalignment check blueprint (drawing number N13581-A) showing a full-size pickup/Bronco-type ladder frame in two views: a plan (top) view with diagonal cross-check…
• Ford Bronco Track Bar / Axle Bracket Dimensions - AutoCAD Blueprint Template
  This document is a screenshot of AutoCAD 2007 displaying a fully dimensioned 2D drawing from a file named "Wheel offset.dwg." The drawing shows a flat, roughly C-shaped bracket or plate with a deep U-shaped cutout on…
• Ford Bronco Lower Track Bar Mount Bracket Blueprint - 3/8" Plate Dimensions
  This document is a simple fabrication blueprint (dimensioned line drawing) for a lower track bar mount bracket, uploaded to a 1995 Ford Bronco gallery on SuperMotors.net. The drawing shows a flat plate cut from .375"…
• 1980-96 Ford Bronco Aluminum Body Mount Puck Blueprint - Dimensions & Specs
  This is a machining blueprint from YIKESFAB, LLC (drawn by B. Beeler, dated 01-03-10) for a complete set of custom body mount pucks (bushings) for 1980-1996 Ford Broncos, to be machined from 6061-T6 aluminum. Four puck…
• 1995 Ford Bronco Radius Arm Frame Mount Bracket Blueprint - Dimensions Drawing
  This document is a screenshot of an AutoCAD 2007 session displaying a dimensioned 2D blueprint from a file named "Wheel offset.dwg," uploaded as part of a set of radius arm frame mount drawings for a 1995 Ford Bronco…
• Ford Bronco Radius Arm Frame Mount Bracket Blueprint - Hole Dimensions (CAD)
  This document is a screenshot of an AutoCAD 2007 session showing a dimensioned 2D blueprint of a flat plate/bracket, saved as "Wheel offset.dwg." The part is roughly 10 1/4 inches wide by 9 7/8 inches tall with a…
• 1995 Ford Bronco Bracket Blueprint - Wheel Offset Drawing Dimensions (AutoCAD)
  This document is a screenshot of AutoCAD 2007 displaying a drawing file named "Wheel offset.dwg" (path: C:\Documents and Settings\Mike\My Documents\Drawings\). The drawing shows a rectangular bracket in side/elevation…
• Ford Bronco Radius Arm C-Bracket Dimensions - CAD Blueprint with Hole Locations
  This document is a screenshot of AutoCAD 2007 showing a fully dimensioned 2D blueprint of a bracket-shaped part (file name "Wheel offset.dwg," uploaded to the vehicle album as "RA C Dims.jpg," suggesting it depicts…
• Ford Bronco Roll Cage Frame Bracket Blueprint - Dimensions & Hole Layout
  This document is a hand-drawn dimensional blueprint for a cage frame bracket, uploaded to accompany a 1995 Ford Bronco. The drawing shows a rectangular bracket plate 10 1/4 inches long and 3 5/8 inches tall. Two 1-inch…
• 1995 Ford Bronco Roll Cage Frame Bracket Blueprint - Hole Dimensions Template
  This document is a hand-drafted dimensioned blueprint for a 'cage frame bracket,' uploaded to the gallery of a 1995 Ford Bronco. The drawing shows a flat plate bracket with a rectangular upper portion and a tapered…
• Fold-Out Camp Kitchen Blueprint - Sink & Stove Plan (1996 Ford Bronco Build)
  This document is a CAD-style blueprint (filename 'Kitchen Plan-1.JPG') for a fold-out camp kitchen unit, apparently designed to be built and carried in a vehicle such as the uploader's 1996 Ford Bronco. It contains a…
• Trailer Top View Blueprint - Cooler & Propane Layout Plan (1992 Ford Bronco Gallery)
  This document is a screen capture of a computer-drawn blueprint (top/plan view) apparently created in a diagramming program such as Visio, showing the layout of what appears to be a small utility or camping trailer…
• Rear View Blueprint - Smoker/Firebox Build with 3" Square Tube Frame & Angle Iron
  This document is a computer-drawn (CAD/Visio-style) blueprint titled "Rear.jpg", uploaded to a 1992 Ford Bronco gallery and part of a set including "Firebox side" and "Top" drawings. It depicts the rear elevation of a…
• Firebox Trailer Side View Blueprint - Cooler & Propane Layout (CAD Sketch)
  This document is a screenshot of a CAD/drawing-program layout (likely Visio or similar, shown on a grid with a ruler scaled in inches from 0 to about 130) depicting a side-view plan of a trailer or firebox rig. A scale…
• 90Beater Rock Sliders Blueprint - DIY Ford Bronco Slider Dimensions & Materials
  This document is a homemade blueprint titled "90Beater Rock Sliders," showing how to fabricate a set of DIY rock sliders (side frame protection) for a truck, credited to Topher's World (www.tophersworld.com). A…
• Ford Bronco DIY Rock Sliders Blueprint - Dimensions, Cut List & Materials
  This document is a homemade blueprint titled "90Beater Rock Sliders" showing how to fabricate a set of rock sliders (side frame protection bars), hosted/credited to Topher's World (www.tophersworld.com). The drawing…
• Osnova (Base) Part Blueprint - Steel 40X GOST 4543-71 Machining Drawing (Niva-FAQ)
  This is a Russian-language engineering blueprint (GOST-format A4 drawing) for a machined part titled "Основа" (Base/Foundation), watermarked WWW.NIVA-FAQ.MSK.RU. The drawing shows three views of a flat bracket-like…
• Osnova (Base) Part Blueprint - Steel 40Kh GOST 4543-71 Drawing, Niva-FAQ
  This is a Russian-language engineering blueprint (A4 format, scale 1:1) for a machined part named "Основа" (Base/Foundation), sourced from the website WWW.NIVA-FAQ.MSK.RU. The part is to be made from Steel 40Х (40Kh)…
• Cross-section drawing of a machined pulley body with Ø30.0, Ø35.00, Ø36.00 and Ø40.4 diameters and 15.60, 14.20 and 13.50 widths.
• Cross-section drawing of a grooved pulley assembly on a RODAMIENTO 6003 bearing, dimensioned from Ø14.0 to Ø36.00 and 24.00 wide, ESCALA 3/1.
• Ford Bronco DIY Bracket Blueprint - .375" Plate with .75" Hole, Dimensions
  This document is a simple CAD-style dimensioned blueprint (drawing) of a flat steel plate part, uploaded to a 1994 Ford Bronco gallery. The drawing specifies the part is to be cut from.375" (3/8-inch) plate. Overall…
• Ford Bronco Rock Slider Blueprint - DOM Tube Step Dimensions & Parts List
  This document is a CAD blueprint (watermarked "Scheki Design") for a fabricated rock slider / step assembly, uploaded to the gallery of a 1995 Ford Bronco under the filename RocksliderBitmap.JPG. It shows a dimensioned…
• Ford Bronco Custom Rear Bumper Blueprint - Receiver Hitch Fabrication Dimensions
  This document is a CAD blueprint/dimensioned drawing for a custom rear bumper with an integrated receiver hitch, drawn against the rear elevation of a Ford Bronco-style full-size SUV. The upper portion shows the rear…
• Ford Bronco Bedside Panel & Pocket Cover Blueprint - Dimensions Template
  This document is a hand-drawn dimensional blueprint (uploaded to a 1996 Ford Bronco gallery) showing the layout and measurements of a bedside interior panel and its matching pocket cover. The main drawing, labeled…
• Custom Tank Blueprint Sketch - Hand-Drawn Dimensions (48" x 38") Ford Bronco
  This document is a hand-drawn dimensional sketch on graph paper, uploaded as "tank.jpeg" to a 1992 Ford Bronco gallery and signed/labeled "MARK RICHARDS." It appears to be a homemade blueprint for a custom tank (likely…
• 1994 Ford Bronco Cargo Table Blueprint - Sub Box Platform Dimensions (66.9 in)
  This document is a CAD-style blueprint (two orthographic views) of a custom truck table or cargo-area platform, uploaded as part of a car audio installation build set for a 1994 Ford Bronco. The top (plan) view shows a…
• Truck Table Blueprint with Subwoofer Box - 64x34 in Dimensioned Plan (Bronco Audio)
  This document is a dimensioned blueprint-style drawing (appearing to be CAD output) of a custom table, uploaded as part of a set of car audio installation plans for a 1994 Ford Bronco. The top view shows a rectangular…
• 1994 Ford Bronco Custom Sub Box Top View Blueprint - Enclosure Dimensions
  This document is a hand-drafted or CAD-style blueprint titled by its uploader as "Sub Box Top.jpg," showing a top-view plan of a custom subwoofer enclosure intended for installation in a 1994 Ford Bronco. The drawing…
• Subwoofer Box Cut Sheet - Panel Dimensions for Custom Sub Enclosure (Ford Bronco)
  This document is a cut sheet (blueprint-style panel layout) for building a subwoofer enclosure, uploaded to accompany a 1994 Ford Bronco custom audio installation. It shows three grouped diagrams of rectangular panels…
• 1978 Ford Bronco Rear Quarter Panel Template - Hand-Drawn Measurements
  This document is a hand-drawn dimensioned template (blueprint sketch) of a vehicle rear side panel, annotated with dozens of measurements for reproducing or fabricating the panel. The overall panel is dimensioned at 61…
• Ford Bronco Side Body Panel Template Blueprint with Hole Locations & Dimensions
  This document is a CAD-style blueprint or template drawing of an automotive side body panel, uploaded to a 1994 Ford Bronco gallery under the filename 'side panel.jpg'. The drawing shows the full perimeter outline of…
• Lot Plan CAD Drawing - Property Site Plan Sketch (1995 Ford Bronco Gallery)
  This document is not a scanned automotive reference; it is a screenshot of a CAD drawing (consistent with AutoCAD's dark model-space interface, grid visible) titled by the uploader as "LOT PLAN.jpg." The drawing shows…
• Spicer Driveshaft Yoke Diagram - U-Joint Bearing Cap Bore "D" Measurement
  This document is a simple technical line drawing (blueprint-style) of a Spicer-type driveshaft yoke, shown in side view. The only text visible on the drawing is the single letter "D," which labels a circled callout…
• 9-LED Square Work Light Dimensions Diagram - 110mm x 138mm, M8 Stud Mount
  This document is a dimensioned line drawing (blueprint-style) of a square 9-LED work lamp, distributed by SUNYEE International (whose logo/watermark appears twice on the image). The front view shows a square housing…
• Handwritten Fabrication Sketch with Dimensions - 1996 Ford Bronco Owner Notes
  This document is a handwritten pencil sketch on yellow lined notebook paper, photographed at an angle with a red mechanical pencil lying across it. It is not a printed automotive reference; it is a rough…
• Hand-Drawn Measurement Sketch (60 x 25/25, 3 ends) - 1996 Ford Bronco Gallery
  This document is a rough hand-drawn pencil sketch on lined yellow notebook paper, photographed rather than scanned. It shows a single rectangle with dimension callouts: the long side is marked "60," with an adjacent…
• Hand-Drawn Cabinet/Storage Box Sketch with Dimensions - 1996 Ford Bronco Gallery
  This document is a single page from a lined notepad containing a freehand pencil sketch, apparently a perspective drawing of a base cabinet or similar built-in structure, with handwritten dimensions and notes. The…
• Handwritten Plywood Cabinet/Shelf Plan Sketch - Materials & Cut Layout Notes
  This is a scanned page of handwritten pencil notes and sketches on yellow lined notebook paper. Despite being uploaded to an automotive gallery for a 1996 Ford Bronco, the content is a woodworking plan, apparently for…
• 1996 Ford Bronco SAS Hand Sketch - 7" Rod End & 3-1/2" Offset Dimensions
  This is a hand-drawn, dimensioned sketch (a rough blueprint/template) made in marker on a piece of corrugated cardboard, uploaded to the gallery of a 1996 Ford Bronco under the filename SAS 075.jpg. The drawing depicts…
• 1996 Ford Bronco SAS Radius Arm/Link Cardboard Template - 38.5" Layout Sketch
  This is a photograph of a home-made, full-scale layout drawing sketched in marker on a large piece of cardboard resting on a work surface in a garage. The sketch appears to be a template for fabricating a suspension…
• Bend-Tech PRO Roll Cage Side Tube Bend Specs - 1996 Ford Bronco, 2.00 DOM
  This is a screenshot of the Bend-Tech PRO tube bending software showing two open documents (Document 2 and Document 3), each defining one side tube of a roll cage design, apparently mirrored left/right pieces for a…
• 1995 Ford Bronco Tonneau Cover Dimensions - Cutting Template Diagram
  This document is a simple dimensioned outline drawing, uploaded as 'Tonneau Cover Dimensions' for a 1995 Ford Bronco. It shows the flat-pattern shape of a tonneau cover (or similar panel) with all key measurements…
• Chevy vs Ford Front Spindle Comparison Diagram - Dimensions & Differences
  This document is a dimensional comparison blueprint of two front axle spindles, one labeled CHEVY and one labeled FORD, drawn side by side in profile. The Chevy spindle has an overall length noted as 6 1/2 while the…
• Ford Bronco Custom Bumper Blueprint - 2x2 Tube & Angle Iron Fab Sketch
  This document is a faxed, hand-drawn fabrication blueprint (fax header: MAY-30-02, OTR TRANSPORT INC, 9722899839, page P.05) for a bumper or similar cross member, uploaded to a 1995 Ford Bronco gallery. The sketch…
• Custom Subwoofer Box Grille Top Blueprint - 1994 Ford Bronco Audio Build
  This document is a text-free CAD blueprint drawing uploaded to a 1994 Ford Bronco gallery as part of a custom car-audio build set (filename: 'speaker box with grill top.jpg'). It depicts a top (or face) view of a…
• Custom Subwoofer Box with Grille Side View Blueprint - 1994 Ford Bronco Audio
  This document is an untextured CAD-style line drawing showing the side view of a custom subwoofer/speaker enclosure with its grille installed. The drawing depicts a large rectangular box body with a thin grille panel…
• Custom Subwoofer Box Grille Blueprint - Perforated Speaker Panel Drawing
  This document is a blueprint-style line drawing, uploaded as 'box with grill.jpg' as part of a custom car-audio build set for a 1994 Ford Bronco. It depicts a rectangular panel, apparently the front grille of a…
• 1994 Ford Bronco Custom Rear Speaker Table Blueprint - Sub Box & Oval Speakers
  This scan, uploaded as "rear Table.jpg" to a 1994 Ford Bronco gallery, is a text-free CAD-style line drawing (blueprint). It appears to show a rear view of a custom audio installation table or panel for the vehicle…
• 1994 Ford Bronco Custom Subwoofer Box Blueprint - Wireframe CAD Enclosure Plan
  This document is a wireframe isometric line drawing, apparently produced in a CAD program, showing the three-dimensional structure of a custom subwoofer enclosure (sub box). The drawing depicts a rectangular box viewed…
• Hand-Drawn Fabrication Sketch - 17" Panel with 1/2" Notch (1996 Ford Bronco Gallery)
  This document is a hand-drawn pencil sketch on lined notebook paper, uploaded as a 'blueprint' in a 1996 Ford Bronco owner's gallery. It is not a printed factory diagram; it appears to be a fabrication or…
• Ford Bronco Roll Cage Side View - Bend-Tech PRO Design Screenshot
  This document is a screenshot of the Bend-Tech PRO tube-bending CAD software, captured on 1/19/2010 at 8:59 PM, showing an assembly file named "2010 Bronco Cage (jane 17a).bta" located in C:\2020SSI\Bend-Tech…
• Ford Bronco Roll Cage Design - Bend-Tech PRO 3D Wireframe Blueprint (2010)
  This document is a screenshot of the Bend-Tech PRO tube-bending/fabrication CAD software (running on Windows XP) showing a custom roll cage design for a Ford Bronco. The window title identifies the open assembly file…
• Ford Bronco Roll Cage Design - Bend-Tech PRO 3D Wireframe Blueprint
  This document is a screen capture of Bend-Tech PRO tube-bending/CAD software displaying a custom roll cage design saved as 'Bronco 1.bta'. The main viewport shows a 3D wireframe assembly of the complete cage, including…
• Ford Bronco Radius Arm Angle Measurement Sketch - Arm vs Garage Floor Degrees
  This document is a simple hand-made sketch (blueprint-style line drawing) uploaded to a 1996 Ford Bronco gallery. It depicts angle measurements taken on a suspension radius arm relative to a garage floor. The drawing…
• 1995 Ford Bronco Tube Bending Blueprint - Roll/Light Bar Bend Angles & Dimensions
  This is a hand-drawn pencil fabrication blueprint (not a factory document) showing three views, TOP MAIN, FRONT, and SIDE, of a bent-tube structure, most likely a roll bar, light bar, or tube bumper for the uploader's…
• Ford Bronco Clevis Mount Bracket Sketch - Frame Horn Tow Hook Mount Diagram
  This document is a simple hand-drawn line sketch (blueprint-style) of a clevis mount bracket, uploaded to the gallery of a 1993 Ford Bronco under the filename 'clevismounts.gif'. The drawing shows an angled…
• Ford Bronco Transfer Case Skid Plate Blueprint - 1x1 .25 Wall Tubing Layout
  This document is a simple homemade blueprint/sketch for a transfer case skid plate, uploaded to a 1995 Ford Bronco gallery. It contains two views. The 'Rear Profile' view shows a horizontal plate (drawn as a black bar)…
• Ford Bronco Rock Slider Blueprint - Tube Sizes, Weights & Frame Mount Design
  This is a hand-drawn blueprint/sketch for fabricating rock sliders (frame-mounted side protection bars) for a Ford Bronco. The drawing shows a 66-inch slider assembly attaching to the Bronco frame using four legs made…