The story
---Current Mods and Features---
-45 Gallon Fuel Cell
-On Board Air, York Compressor
-Onboard Welder
-Pair of KC Daylighters Up Front
-Custom Rewired Fuse/Relay panel
-Custom Battery Tray
-Rewired Wiring Harness
-8 Point Roll Cage
-5 Point Racing Seat Belts
-Racing Seats
-Custom Tube Inner Front Fenders
-Cobra NightStalker CB
-MP3 player
-Auto Meter Guages
-Kayline Soft Top
-G3 130 Amp Charging System
-800 CC RedTop Optima
-Two 900 CCA Optima Yellow Tops
-Tow Hooks Front And Back
-Saginaw PS pump
-Hydro Assist Steering
-Heim Joint Track Bar
-Chevy 1 ton TRE's
-Front and Rear 1350 Drivelines. Drivelines are 1/4" Difference in lenghts necessatating only 1 spare drive line to be carried when wheeling
-12000 lb Warn Winch
-Rock Sliders / Rocker Protection
-Rock Lights
-Rear Seat with storage under it for camping
-4 Ammo cans bolted in the bed for storage. 1 Tools, 1 Spare parts, 1 Spare fluids, 1 Camping gear... Still Room between them for a 100 qt cooler for food.
-Beafy Gas Tank Skid Plate
-Heim Jointed Extended Radius Arms
-Heavy duty rear bumper with swing gate storage
---Future Mods And Features To Come---
-On Board Shower
-Electronic Fuel Injection
-Rear Disc Brakes
-Onboard Water storage tank — Don Rowles
Photos
Soft top in peices. Owner
putting the mounting brackets on the body. Owner
Brackets all on. Owner
placing buttons on soft top. Owner
Almost completed. Owner
Soft Top all complete Owner
Engine and Running. Owner
Cam Specs that I used. lopey idle when cold but smooth when warmed up. But just enough to know there is some majoy ponies between the fende… Owner
Nice clean empty block Owner
Cam is going in... Owner
Crank going in... Owner
Plastiguagin the mains. Owner
Crank and Mains all installed. Owner
Ford Motor Sport Roller Rockers. *drool* Owner
Heads on, Push Rods being put in. Owner
Rollers installed and being Torqued down. Owner
Painting the Block up. Owner
Oil pan Gasket being set into place. Owner
Oil plan placed on block. Owner
Valve Covers on. Owner
I knew it was gonna be a thirsty engine but I never thought it would eat as well. Owner
New Flywheel, Clutch and pressure plate installed. Owner
Battery Tray Owner
Alot of Wires Pulled out Owner
MSD Offroad installed Owner
Removed a birds nest of excess wiring. Owner
Another shot of excess wires removed. Owner
New fuse panel / relay board under way. Owner
Wiring the fuses up. Owner
Fuses all wired up. Owner
Grounds for the Relays Owner
Hot power wired to Relays from fuses. Owner
Mounted under the dash. Put on hinges to be out of the way, yet easily gotten to when needed to fix. Owner
Leaky 9"....bad things to come ahead. Owner
Bandaid. Only to find out later the ring gear would explode and loose half of the teeth on it destroying my second 9" 3rd member. Owner
Dana 44 Axle truss. Didn't loose any ground clearance in my mind, and it takes one hell of a pounding. Owner
8 lug chevy dana 44 outters. They fit nicely on the Ford axle. Owner
Just a little caliper grinding to fit 15" rims with 2.75" back spacing Owner
My dana 44 installed from the 76 F-150 and 8 lug outters on it. Owner
Front axle completely installed and the SX's are mounted. Owner
No comments yet — be the first to add to the record.