SuperMotors SuperMotors SUPERMOTORS Search: try “orange Bronco on 35s”
1992 Ford Bronco “the bitch”

“the bitch”1992 Ford Bronco

documented by redrumybronco 54 photos documented since ♡ Follow this build

The story

I enjoy working on my truck. I have done all of my modifications using simple and cheap garage tools. I have saved thousands of dollars doing it myself. · redrumybronco

Photos

1992 Ford Bronco: Started off by removing part of the rain gutter 1992 Ford Bronco: cut a slot in the sheet metal where the horizontal joint is visible 1992 Ford Bronco: Welded a reinforcemant 1/8"x1" (you can barely see it sticking out) 1992 Ford Bronco: this is the sheet metal reinforcement 1992 Ford Bronco: filled and primered, not ready for paint yet Close-up of a gray primered body panel corner on a vehicle under a tent 1992 Ford Bronco interior showing two blue speakers and a black toolbox in the cargo area Blue NOS nitrous bottle and NOS controller mounted in a vehicle interior panel 1992 Ford Bronco: 150 watt Alpine amp Close-up of a blue NOS nitrous bottle and NOS electronics mounted in a trunk 1992 Ford Bronco: amp for mid range speakers 1992 Ford Bronco: Cooling fan light 1992 Ford Bronco: Vehicle interior showing two blue cylindrical speakers with purple lights, facing rearward. Seats and dashboa… 1992 Ford Bronco: Drill and tap Metal linkage joint and rod under a vehicle with masking tape nearby Close-up of a metal engine part covered with tape and paper towels 1992 Ford Bronco: locktite and srew in 1992 Ford Bronco: only time will tell if this will hold, but this is much better than before 1992 Ford Bronco: Black painted upper rear quarter panel and door window frame of a vehicle under a tent Close-up of dark-colored vehicle body panel with window trim and a small antenna-like protrusion. Watermark r… 1992 Ford Bronco: Swing-away spare tire carrier with mounted all-terrain tire and Hi-Lift jack Spare tire carrier modification with Hi-Lift jack mounted Close-up of a black metal spare tire carrier with a tire and brake rotor visible 1992 Ford Bronco: body damage by spare tire carrier 1992 Ford Bronco: welded a metal bracket 1992 Ford Bronco: some paint to prevent rust Red Lincoln Electric Weld Pak 3200 welding machine on a cart with four wheels Red welding cart with black frame and wheels Red Lincoln Electric Weld Pak welding machine on a four-wheeled cart 1992 Ford Bronco: The Rancho kit came with two add-a-leafs and so I had to remove a stock leaf from each side. Recycled the old… 1992 Ford Bronco: 2.5 degree shim plus cut up leafs = 1-1/2" lift The Rancho kit raises the rear 3" and the front 4". Need an a… 1992 Ford Bronco: I had to devise a way so that the leaf center bolt would be able to fit into the stock shim 1992 Ford Bronco: bottom of rancho shim, the hole is tappered 1992 Ford Bronco: cut a shock mount sleeve and welded the edge in to fill in the tappered hole 1992 Ford Bronco: looking from the top, pipe wedge is not welded to aluminum degree shim just wedged in 1992 Ford Bronco: although this looks kinda funny, the three cut up leafs only lift about 1". It is way better than the smaller… 1992 Ford Bronco: close up of the leaf center bolt catching the pipe wedge 1992 Ford Bronco: driveline angle corrected 1992 Ford Bronco: removed shock mounts for re-positioning 1992 Ford Bronco: shock mount welded at 15 degrees

Albums · 9

How the owner organised this build. Open an album for every photo in it.

The peanut gallery

No comments yet. Be the first to add to the record.

Spotted in the wild

Seen this vehicle at a show or on the trail? Add your shot. The owner approves it onto the record.