SuperMotors SuperMotors SUPERMOTORS Search: try “orange Bronco on 35s”
Join
1986 Ford Bronco front 3/4 view in snow
Home/ Registry/ Ford/ Bronco/ 1980-1986/ 1986 Bronco supermotors.net/registry/4636

1986 Ford Bronco

documented by cloim 47 photos documented since ♡ Follow this build

Photos

1986 Ford Bronco front 3/4 view in snow Chrome exhaust headers on a wooden surface chrome exhaust headers on a wooden surface Two metal exhaust components, one labeled CATCO, on a wooden surface Catalytic converter interior with "12K" visible on honeycomb structure Close-up view of the inside of an exhaust pipe with a smaller pipe inside close-up of rusty exhaust pipe connection under a vehicle 1986 Ford Bronco: Exhaust manifold and pipe connection on an engine, showing rust and bolts Exhaust pipe with a hole cut into it 1986 Ford Bronco: Cats and crossover pipe removed 1986 Ford Bronco: Passenger side installed. 1986 Ford Bronco: Drivers side installed 1986 Ford Bronco: No clearance between header and frame on passenger side. 1986 Ford Bronco: Starter looks like it will require header removal for access. A heat shield might also be a good idea. 1986 Ford Bronco: Collector exits lower than it should. Exhaust will have to rise up a couple inches to clear the tranny crossm… 90 Bronco. O2 sensor placement? 90 Bronco. Lower t-crossmember? 1986 Ford Bronco: fuse panel diagram 1986 Ford Bronco: Poly hd motor mount from JBG Rusty metal bracket with a cylindrical pin inserted into a hole Rusted metal bracket with a bolt and cable Custom metal engine mount bracket bolted to engine block and frame 1986 Ford Bronco: bottom of tranny mount 1986 Ford Bronco: Stock air inlet 1986 Ford Bronco: Temporary solution using 2"pvc pipe 1986 Ford Bronco: 3a Racing exhaust tip. End-view. 1986 Ford Bronco: 3a Racing tip. Side view 1986 Ford Bronco: Dynomax J-bend 1986 Ford Bronco: Loop style exhaust hanger 1986 Ford Bronco: O2 sensor fitting. 1986 Ford Bronco: Modified hangers 1986 Ford Bronco: header stud and header bolt. Studs aid in aligning the header while installing. I was only able to use 4 stud… 1986 Ford Bronco: after cutting 1986 Ford Bronco: Deburring the interior is easiest with a deburring tool. IExterior with a file. I used a file for both. 1986 Ford Bronco: The OD of the pipe through the bend radius is slightly smaller than the ID of the pipe through the straight s… 1986 Ford Bronco: Pipe from drivers side collector to the cat. 1986 Ford Bronco: Trimming a little off... 1986 Ford Bronco: Fully welded and ready to install... Almost. Still need to tweek a couple things (cut and reweld) but it's go… 1986 Ford Bronco: Custom hanger installed. Passenger side to drivers side exit balances well at this point. I chose a simmilar… 1986 Ford Bronco: Cat forward view.
Browse all 47 photos

Albums · 9

How the owner organised this build. Open an album for every photo in it.

General - 1986 Ford Bronco General 1 photo header install - 1986 Ford Bronco header install 15 photos Jerrys exhaust - 1986 Ford Bronco Jerrys exhaust 2 photos electrical - 1986 Ford Bronco electrical 1 photo electric fan - 1986 Ford Bronco electrical / electric fan 4 photos mounts - 1986 Ford Bronco mounts 5 photos fipk - 1986 Ford Bronco fipk 2 photos exhaust - 1986 Ford Bronco exhaust 16 photos emissions - 1986 Ford Bronco emissions 1 photo
See every Ford Bronco in the registry The 1980-1986 Ford Bronco registry

The peanut gallery

No comments yet. Be the first to add to the record.

Spotted in the wild

Seen this vehicle at a show or on the trail? Add your shot. The owner approves it onto the record.