SuperMotors SuperMotors SUPERMOTORS Search: try “orange Bronco on 35s”
Join
Mud-splattered white Ford Bronco on grass, low front angle, black hood deflector, BFGoodrich All-Terrain tires
Home/ Registry/ Ford/ Bronco/ 1992-1996/ “Rio” supermotors.net/registry/26682

“Rio”1996 Ford Bronco

documented by thebroncofanatic 57 photos documented since 1 years documented ♡ Follow this build

The story

This truck was from georgia so the frame and body are very clean and i got it fairly cheap but there was no interior in the truck, the previous owner was going to make it a mud truck but decided the body was too good for that purpose. Right now i have the interior out of a 1989 eddie bauer bronco because it matched the tan dash. I will be on the hunt for a 92-96 tan interior. I have done a lot of work to the bronco since i bought it in spring 2014 and i will continue wrenching and wheeling as long as i have the time and money · thebroncofanatic

Photos

1996 Ford Bronco: When i first got her 1996 Ford Bronco: Late spring 2014 White Ford Bronco parked on a grassy lawn, rear-mounted spare tire visible White 1996 Ford Bronco rear view with spare tire mounted on the tailgate 1996 Ford Bronco: As she sits now after getting back from the wood county 4 wheelers club mud bog in bradner OH Soft top from bronco graveyard 1996 Ford Bronco with a black soft top, covered in mud splatters, parked on grass 1996 Ford Bronco: White Ford F-Series truck parked on grass, front view. License plate reads G01 2062 1996 Ford Bronco: Just dipped a toe in the mud 1996 Ford Bronco: Rough country single steering stabilizer Pre-assembled it. The 2 bolts in the upper left are for f2 and f350s… 1996 Ford Bronco: Its best to attach the bracket up front and slide it back because of the inner fender being in front of the t… 1996 Ford Bronco: Slid the bracket to the correct locattion behind that metal stud 1996 Ford Bronco: Extended the shock absorber 4.5 inches and attached the tie rod bracket and u bolts 1996 Ford Bronco: Rotated the bracket into a location where it wouldnt bind and tightened evrything up 1996 Ford Bronco: Kept the bolts parallel to the ground while i was tightening them 1996 Ford Bronco: Just about finished 1996 Ford Bronco: Done Added the included sticker for the cool factor As for functionality it works great, takes all the play o… 1996 Ford Bronco: C150 centurion i found on a snowmobile trip in Gaylord, Michigan the first one i have ever seen in real life… 1996 Ford Bronco: Ford truck with snow on top, front grille visible, parked in a snowy driveway 1996 Ford Bronco: White Ford truck with camper shell in snow, 3/4 front view. Visible badge indicates 1992 model year 1996 Ford Bronco rear view in snow, license plate BWD 4777 1996 Ford Bronco parked in snow, side view. Another truck is visible to the left 1996 Ford Bronco: Very clean, for a michigan truck you cant see it but theres some rust on the bottom of the rockers but still… 1996 Ford Bronco: Cold air intake kit i bought on ebay. Search 5.8 intake. This is a cheap kit from china but i diddnt want to… 1996 Ford Bronco: Removed stock intake Note: broken chunk of the snorkel from PO 1996 Ford Bronco: Got the maf attached to the adaptor and the air intake temp sensor locked into the bung 1996 Ford Bronco: All pieces assembled and adjusting to fit 1996 Ford Bronco: Universal bracket in the kit. I used the existing air box screw and bent a 90 degree in the bracket to fit 1996 Ford Bronco: Good shot of the air temp sensor 1996 Ford Bronco: Engine bay showing an aftermarket red cone air filter and chrome intake tube. Brake fluid reservoir is visible engine bay with red cone air filter and chrome intake piping 1996 Ford Bronco: End result the intake works well. There is better throttle response, slightly improved mpg, a more throaty so… 1996 Ford Bronco: Guide to fuel pump replacement I made an access panel in the floor its about 8x11" I measured and cut it out… 1996 Ford Bronco: View through a cut-out in the vehicle floor to the fuel tank and fuel lines. 1996 Ford Bronco: The cut panel Im going to make it hinged and reseal it to the floor 1996 Ford Bronco: Gas tank ring removed. It is important to keep the area around the pump clean and free of dirt 1996 Ford Bronco: Quick disconnect tool I used about $5 at an autoparts store 1996 Ford Bronco: Got the pump and sender out and as you can tell the pump has been replaced before because of the butt connect… 1996 Ford Bronco: Fuel pump assembly with hoses and electrical connectors 1996 Ford Bronco: There are 3 1/4 screws that holt the pump to the sender and float assembly that need to be removed
Browse all 57 photos

Albums · 7

How the owner organised this build. Open an album for every photo in it.

a few pics - 1996 Ford Bronco a few pics 10 photos steering stabilizer install - 1996 Ford Bronco steering stabilizer install 8 photos centurion sightings - 1996 Ford Bronco centurion sightings 6 photos cold air intake install - 1996 Ford Bronco cold air intake install 9 photos fuel pump replacement - 1996 Ford Bronco fuel pump replacement 10 photos prerunner lightbar - 1996 Ford Bronco prerunner lightbar 10 photos missing center cap inserts - 1996 Ford Bronco missing center cap inserts 4 photos
See every Ford Bronco in the registry The 1992-1996 Ford Bronco registry

Technical reference · 1992-1996 Ford Bronco

Factory documentation members uploaded for this generation, sorted by how much of it there is.

Wiring Diagrams (411) Exploded Parts (169) Service Procedures (142) Data/Spec Plates (103) Manual Pages (98) Schematics (95) Brochures & Literature (81) Blueprints (81) Vacuum Routing (40) Fuse & Relay Charts (15) Torque Specs (13)

The peanut gallery

No comments yet. Be the first to add to the record.

Spotted in the wild

Seen this vehicle at a show or on the trail? Add your shot. The owner approves it onto the record.