Manual Pages: Nissan Micra 1983-1992

Technical Reference

Member-uploaded diagrams & documents for this generation. AI-classified; community-verified where badged.

Manual Pages

• Nissan Micra Power Supply Routing - Fuse & Fusible Link Check (EL-6)
  This is page EL-6, titled "POWER SUPPLY ROUTING," from a Nissan service manual, uploaded to accompany a 1990 Nissan Micra. The page covers two topics: fuses and fusible links. The Fuse section includes an illustration…
• Nissan Standardized Relay Chart EL-4 - 1T, 1M, 2M, 1M-1B Types & Case Colors
  This is a scanned page (EL-4) from a Nissan service manual's Electrical System section titled "Standardized Relay." It presents a reference table identifying the four standardized relay types used in the vehicle: 1T…
• Nissan Micra Harness Connector Description - How to Disconnect Connectors (EL-2)
  This is a service manual page from the Electrical (EL) section, page EL-2, titled "HARNESS CONNECTOR: Description." It explains that all harness connectors are designed so they do not become loose or disconnected…
• Nissan Special Service Tools ST-13 - R22T Steering Tools & Kent-Moore Numbers
  This is page ST-13 of a Nissan factory service manual, from the Steering (ST) section, titled "SPECIAL SERVICE TOOLS." It is a table listing the special service tools required for servicing the R22T steering unit…
• Nissan Micra Service Manual GI-6: Wiring Diagram Symbols & Wire Color Codes
  This is page GI-6 from the General Information section of a Nissan factory service manual, titled "HOW TO USE THIS MANUAL." Item 10 explains the symbols used in the manual's wiring diagrams via an annotated example…
• Nissan Micra Service Manual GI-5 - How to Use This Manual, Symbols & Units
  This is page GI-5 from the General Information (GI) section of a Nissan factory service manual, titled "HOW TO USE THIS MANUAL." It explains conventions used throughout the manual. Item 7 describes how small…
• Nissan Micra Service Manual GI-4: How to Use This Manual & Front Axle Example
  This is page GI-4 from a Nissan factory service manual's General Information section, titled "HOW TO USE THIS MANUAL." It explains six conventions used throughout the manual: a quick reference index with black section…
• Nissan Micra Service Manual - General Information (GI) Section Contents Page
  This document is the title/contents page of the General Information (GI) section of a factory service manual, scanned and uploaded as part of a larger multi-page manual set attributed to a 1990 Nissan Micra. The page…
• Nissan Micra Service Manual Section EL - Electrical System Contents Page
  This document is the title/contents page of Section EL (Electrical System) from a Nissan factory service manual, uploaded as part of a manual set for a 1990 Nissan Micra. It lists the complete table of contents for the…
• Nissan Micra Service Manual BF-3: Clip & Fastener Removal Chart (Cont'd)
  This is page BF-3 of a Nissan service manual, from the General Servicing section, continuing a reference chart of body clips and fasteners ("Clip and Fastener (Cont'd)"). The page presents a table with four columns…
• 1990 Nissan Micra Service Manual BF-2: General Servicing, Clip & Fastener Guide
  This is page BF-2 of a factory service manual (BF: Body & Frame section) titled "General Servicing." It contains two subsections. The "Precautions" section lists five general body-work precautions: using cloth or…
• Nissan Automatic Transmission Control Valve Body Inspection & Assembly - AT-27
  This is page AT-27 from a Nissan automatic transmission service manual section titled "Repair for Component Parts," continuing coverage of the Control Valve Body. The page explains inspection and cleaning procedures…
• Nissan Micra Automatic Transaxle Service Notes & Control Valve Body Diagram AT-3
  This is page AT-3 ("General Service Notes") from the automatic transaxle (AT) section of a Nissan factory service manual, uploaded to a 1990 Nissan Micra gallery. The upper half contains "Repair Notes": general…
• Nissan Micra Engine Fuel & Emission Control (EF & EC) Section Contents Page
  This is the title/contents page of the "Engine Fuel & Emission Control System" section (Section EF & EC) from a factory service manual, uploaded to the gallery of a 1990 Nissan Micra. The page lists the topics covered…
• Nissan Micra Engine Outer Components Torque Specs - Service Manual Page EM-2
  This is page EM-2 from a Nissan factory service manual, Engine Mechanical (EM) section, titled 'ENGINE COMPONENTS: Outer Parts, '. It presents two exploded/side-view line drawings of the engine, one 'From front side'…
• 1987 Nissan Micra VIN Decoder & ID Plate Locations - Service Manual GI-8
  This is page GI-8 from a Nissan Micra service manual's General Information section, titled 'Identification Information: Identification Numbers.' The top half contains a line drawing of a 3-door Micra hatchback showing…
• Section HA Heater title page with contents: Air Flow and Component Layout (HA-2), Door Control (HA-4) and Heater Electrical Circuit (HA-6).
• Page BF-4 clip and fastener table: clip CE104 with shape drawing and removal and installation diagram.
• Section BF contents: general servicing BF-2, body end and door BF-5, interior and exterior BF-11, windshield and windows BF-17, sun roof BF-21.
• Section ST contents: steering wheel, lock and lower joint ST-3, steering column ST-4, manual steering gear and linkage R22T ST-6, tools ST-13.
• Page BR-18 special service tool: GG94310000 flare nut torque wrench, with line drawings of the wrench.
• Page RA-8: KV40102150 bearing outer race drift set with ST35325000 drift bar, KV40102110/120 drifts and KV40102130/140/150 screws.
• Section RA contents: rear axle RA-2, rear suspension RA-5, service data and specifications (S.D.S.) RA-7, special service tools RA-8.
• Page FA-16 tools: HT72520000 ball joint remover, ST35652001 clamp, KV38106300 and KV38105500 oil seal protectors, HT71730000 spring compressor.
• Service data page FA-13: coil spring, strut and drive shaft specs for M/T and A/T, including D569 transaxle side and BF69 wheel side joints.
• Service manual Section FA title page listing contents: wheel hub and knuckle, drive shaft, front suspension, S.D.S. and special service tools.
• Page AT-26 listing free lengths of 14 valve body springs, pressure regulator 46.4 mm (1.827 in), and separating the valve body without losing 6 steel balls.
• Page AT-5 table showing which clutches, low and reverse brake, band servo, one-way clutch and parking pawl apply in each RL3F01A range, with gear ratios.
• Page AT-5 table showing which clutches, low and reverse brake, band servo, one-way clutch and parking pawl apply in each RL3F01A range, with gear ratios.
• Section AT contents for the automatic transaxle, from Description (AT-2) through S.D.S. (AT-67) and Special Service Tools (AT-71).
• Page MT-31 listing KV38106100 preload adapter and the bearing height gauge set with KV38106210, KV38106220, KV38106230 and KV38106240.
• S.D.S. page MT-29 matching measured adjuster clearance to shim size, plus differential side bearing adjusting shims 38453-01800 through 38453-01811.
• S.D.S. page MT-27 for the RS5F41A 5-speed: gear ratios, final drive 3.810 (80/21), main gear end play, baulk ring clearance and snap ring thickness tables.
• Page MT-20 on mainshaft and diff side bearing preload shim selection: removing outer races and shims, fitting adjusters (A) and setting up the special tools.
• Page MT-18 showing dial gauge check with tool KV38106100, side gear to pinion mate clearance 0 - 0.3 mm (0 - 0.012 in), and differential assembly.
• Page MT-17: mainshaft gear end play, then final drive disassembly driving out side bearing inner races and the pinion mate shaft lock pin, plus gear inspection.
• Page MT-16 covering 4th gear, 5th gear bushing and 5th synchronizer install, with 3rd-4th hub snap rings 32279-01802 (2.0 mm) and 32279-01803 (2.1 mm).
• Page MT-15 covering 2nd baulk ring, 2nd gear and 3rd-4th synchronizer hub install, with 2nd gear snap rings 32269-01800 (2.0 mm) and 32269-01801 (2.1 mm).
• Manual transaxle section contents from removal and installation MT-2 through disassembly, preload adjustment, S.D.S. MT-27 and special tools MT-31.
• KV30101200 clutch aligning bar, ST20050100 distance piece, ST20050010 base plate and ST20050240 diaphragm spring adjusting wrench.
• Clutch section contents listing clutch controls CL-2, clutch unit CL-4, S.D.S. CL-7 and special service tools CL-8.
• Section FE contents listing engine control system FE-2, fuel system FE-3 and exhaust system FE-4.
• Special service tool page listing EG17650301 radiator cap tester adapter with a line drawing of the adapter.
• Section LC contents covering engine lubrication, oil pump, water pump, radiator, thermostat, electric cooling fan, S.D.S. and special tool.
• Special service tools page EM-36: KV10107900 valve lip seal puller, KV10111100 seal cutter and WS39930000 tube presser.
• Special service tools page EM-35: engine stand ST05015000, valve spring compressor KV10109250 and piston pin press stand KV10109800.
• Service data page EM-33: bearing clearances, main bearing grades 0-6 (12215-018xx and 12216-018xx) by color, rod bearing undersize, flywheel runout.
• Service data page EM-32: piston ring clearance and gap, piston pin fit, connecting rod center distance 121.5 mm, crankshaft journal grades and runout.
• Service data page EM-31: main journal grades, piston skirt diameter and clearance, plus a bore, piston and ring set conversion table with part numbers.
• Service data page EM-30: intake and exhaust valve seat dimensions incl. 0.5 mm oversize, camshaft journal clearance, cam heights and block flatness.
• Service data page EM-29 for the MA12: valve head, length and stem diameters, valve clearance, spring heights and valve guide specs.
• Service data page EM-28 for the MA12: 4 in-line, 1,235 cc, 71 x 78 mm bore and stroke, O.H.C., firing order 1-3-4-2, 9.0 compression ratio.
• Section EM contents: engine components, compression pressure, timing belt, cylinder head, oil pan and pump, engine overhaul, S.D.S. and special tools.
• Service data page MA-33: clutch pedal height, wheel alignment (camber, caster, toe-in), brake limits, parking brake notches and wheel runout specs.
• General maintenance under the hood and vehicle: washer fluid, coolant, radiator hoses, brake fluid, drive belts, oil and A/T fluid levels, exhaust and leaks.
• General maintenance checks, page MA-4: tires, wheel nuts, rotation every 7,500 miles (12,000 km), alignment, glass, wipers, doors, lights and horn.
• Maintenance under severe driving conditions, page MA-3, listing condition codes A to G with items such as engine oil and filter every 3,000 miles.
• Periodic maintenance schedule, page MA-2, with emission control system and chassis and body maintenance intervals in miles, kilometers and months.
• Maintenance section MA contents: periodic maintenance MA-2, general MA-4, lubrication chart MA-7, engine MA-8, chassis and body MA-18, S.D.S. MA-32.
• Approximate refill capacities, page GI-12: fuel tank 40 L, coolant 4.7/4.3 L, engine oil 2.8/2.6 L, M/T 2.6 L, A/T 6.0 L, washer reservoir 3.0 L.
• Recommended fuel and lubricants: 87 AKI unleaded or leaded fuel, API SF engine oil, API GL-4 gear oil, DEXRON ATF, DOT 3 brake fluid and SAE viscosity charts.
• Dimension table, page GI-10: overall length 3,785 mm (149.0 in), width 1,560 mm, height 1,395 mm, wheelbase 2,300 mm, plus tread, clearance and overhang.
• Quick reference index of the Nissan Micra Model K10 Series service manual listing sections from General Information (GI) to Electrical System (EL).
• Cover of the 1987 Nissan Micra Service Manual with a line drawing of the 3-door hatchback and a handwritten note about oil filter brands.
• Service manual page EL-29: alternator brush lift reassembly note and S.D.S. for A5T21897, rated 12-50 V-A with 14.1-14.7 V regulated output.
• Service manual page EL-22: starter adjusting plate and S.D.S. table for M2T37081 (M/T) and M2T23685 (A/T) with no-load, brush and clearance specs.
• Service manual page EL-8: topping up electrolyte to the MAX level and a graph comparing charging voltage and current of normal and sulphated batteries.
• Service manual page EL-7: How to Handle Battery, with cautions, over-discharge prevention, hydrometer check and electrolyte level warning.
• Service manual page AT-72: special tools J33200 preload shim selector, J34291 shim setting gauge set, J34279 holding fixture and J3289-20 bench mount fixture.
• Service manual page AT-69: diff side bearing preload 2.9-4.4 N·m, 38454-01X60 to X74 adjusting shims, and the shim selection table by Type A and B readings.
• Service manual page AT-68: brake, brake band and oil pump specs, output shaft bearing preload shims 31499-01X, end play 0.25-0.55 mm with 31484-01X shims.
• Service manual page AT-67: K10 MA12 with RL3F01A transaxle, gear ratios, 6.0 L Dexron capacity, and clutch clearances with 31537-01X00 to X04 plates.
• Service manual page AT-66: stall test flowchart tracing too-high or too-low stall speed to clutch, brake, one-way clutch or engine faults.
• Service manual page AT-62: full-throttle vehicle shift speeds checked at 43-57°C (109-135°F) oil, and a shift schedule graph with upshift and downshift lines.
• Service manual page AT-60: trouble-shooting chart for no drive, noise, 1 and 2 range faults, overheating, oil shoot-out, smoke and smell from the charging pipe.
• Service manual page AT-59: trouble-shooting chart for harsh or slipping shifts, failed shifts, poor acceleration and kickdown faults, ranked by probability.
• Service manual page AT-58: trouble-shooting chart ranking on-vehicle and off-vehicle inspection items by probability for no-start, no-drive and shift faults.
• Service manual page AT-57: road test symptom chart covering P, R, N, D, 2 and 1 range shifts against shift quality, slippage, noise and starting symptoms.
• S.D.S. page EF & EC-35: DCZ306-44 MT and DCZ306-45 AT carburetor jets, float levels and idle speeds, plus fuel pressure 19.6 - 26.5 kPa.
• Lifting points and tow truck towing, page GI-15: towing cautions and automatic transaxle limits of below 50 km/h (30 MPH) and less than 65 km (40 miles).
• Identification numbers page GI-9 showing the Nissan identification plate fields and where engine serial and manual and automatic transaxle numbers are found.
• Model variation table for Canada 3-door and 5-door hatchbacks, HLK10 models with MA12 engine, RS5F41A and RL3F01A transaxles, plus prefix and suffix key.
• Precautions page GI-2 covering exhaust ventilation, jacking and rigid rack support, heavy component removal, battery disconnect and hot part burns.
• Nissan quick reference chart for the 1987 Micra with MA12 tune-up data, clutch pedal, front wheel alignment, rear wheel bearing, brake and refill specs.