1993 Ford Bronco

Day one vs. today

Drag to compare 2011 against 2017.

2011 2017

Photo history

120 photos across 7 years — drag the dot to travel through this vehicle’s life. Captions are the owner’s; where there isn’t one, the AI caption fills in.

2011

7 photos added

Close-up view of a vehicle's front steering rack and suspension system, marked with measurement lines. AI caption A low-angle shot reveals the underside of a vehicle, focusing on its mechanical components and tires. AI caption The internal workings of a vehicle's differential are exposed, showing the gears and lubrication. AI caption Close-up view of an open differential housing, showing internal gears and components. AI caption Close-up view of the internal gears of a differential assembly. AI caption Internal view of differential gears, possibly from a Ford rear axle. AI caption A close-up view of a worn differential part, showing significant scoring and pitting indicative of heavy use. AI caption

2012

43 photos added — showing 8

50 amp circuit breaker Owner So here%u2019s a quick write-up on installing Paul%u2019s Punisher valve body. I wasn%u2019t happy with the way my Bronco was shifting. It… Owner First, as with anything you do on your Bronco. Unplug the negative battery terminal. You also do this to reset the computer, so it can lear… Owner Pull the bolts from your transmission pan. I usually start by taking the ones completely out across the front, then drop the ones down the… Owner I then remove the pan and pour the rest into the container. Next pull the filter from the transmission. You%u2019re probably going to get a… Owner Make sure you carefully pull the filter O ring out from the transmission as well. Sometimes it gets stuck up in there. Usually you can pull… Owner I usually clean out the pan and make sure there is not gasket left while the rest of the transmission fluid drips from the bottom into the… Owner Once the filter is out, you can start pulling the bolts off the valve body. I counted 11 bolts and 2 nuts. Owner

2013

6 photos added

Detail of a vehicle's suspension system, showing a nut and pin assembly. AI caption Close-up of a metal alignment part, letters A through P around its circumference. AI caption Diagram illustrating a mechanical linkage, possibly for vehicle alignment, with a SuperMotors watermark. AI caption This document is a chart detailing alignment specifications for Ford and Dodge vehicles. AI caption This document provides installation instructions for Ford/Dodge Dual-Axis Adjustable Bushings, including diagrams. AI caption This image shows a close-up of a vehicle's ABS sensor mount, highlighting the sensor itself. AI caption

2014

13 photos added — showing 8

This digital tire calculator displays various tire measurements and calculations. AI caption A tire size chart displays specifications for various Toyo Open Country M/T tires, including a 36.7-inch diameter option. AI caption Close-up of a vehicle's overhead console, highlighting a clip with a red arrow. AI caption A metal bracket and a car's interior trim piece are shown on a concrete surface. AI caption Engine control module with visible part numbers and barcode. AI caption This is a close-up view of a vehicle's electronic control module, showing its part number and barcode. AI caption This document is a vehicle information sticker detailing emissions compliance and vacuum hose routing, referencing the 1993 model year. AI caption Two engine cylinder heads, showing signs of wear and rust, are displayed with key areas circled in red. AI caption

2015

18 photos added — showing 8

Disassembled headlight assemblies, showing internal components and wiring, likely for a vehicle part replacement or repair. AI caption This Ford electronic control module has patent numbers stamped on its black casing. AI caption This is a Ford Explorer 5.0 upper intake manifold assembly, not a 1993 Ford Bronco. AI caption An engine intake manifold is shown with markings indicating a throttle body spacer for the EGR system. AI caption Various engine components and a "5.0L V8" identification plate are laid out on a blue cloth. AI caption Explorer 5.0 upper intake manifold shown resting on a towel. AI caption Close-up of an aftermarket throttle body assembly with brass fittings. AI caption Close-up of a throttle body, showing a brass vacuum hose fitting highlighted by a red circle. AI caption

2016

26 photos added — showing 8

A drop pitman arm is measured, showing its dimensions on a wooden background. AI caption A rusty drop pitman arm is shown resting on a wooden workbench. AI caption Chrome bumper with black trim, likely for an older truck or SUV, seen indoors. AI caption A close-up view of a vehicle's bumper, surrounded by natural elements like leaves and twigs. AI caption

2017

3 photos added

The peanut gallery