Service Procedures: Hyundai Genesis Coupe 2010-2016

Technical Reference

Member-uploaded diagrams & documents for this generation. AI-classified; community-verified where badged.

Service Procedures

• Hyundai 2.0L Timing Chain Tensioner Access Hole & Valve Clearance - EM-10
  This is page EM-10 from a Hyundai/Kia Engine Mechanical System service manual section covering valve clearance inspection and adjustment. The page instructs the technician to check only the valves indicated for the No…
• Hyundai Genesis Coupe DTC P0017 Crank/Cam Correlation Bank 1 Sensor B - FL-104
  This is page FL-104 from a Fuel System service manual section covering diagnostic trouble code P0017, "Crankshaft Position-Camshaft Position Correlation (Bank 1 Sensor B)." The page begins with three component location…
• Hyundai Genesis 2.0T Timing Chain Install - Alternator, Coil & Intercooler Torques (EM-32)
  This is page EM-32 from a factory service manual section titled "Engine Mechanical System," showing reinstallation steps (steps 14-18) at the end of an engine service procedure, uploaded as part of a timing chain…
• Hyundai Genesis 2.0T Timing Chain Install EM-31: Valve Cover & Pulley Torques
  This is page EM-31 from a Hyundai factory service manual's Timing System section, covering the final reassembly steps after timing chain installation. Step 10 details installing the cylinder head cover: removing…
• Hyundai Genesis 2.0L Timing Chain Cover & Oil Pan Install - Sealant & Torque Specs
  This is page EM-30 from an Engine Mechanical System service manual section, part of a timing chain installation procedure for a 2.0L engine. It covers final steps of timing chain cover installation and oil pan…
• Hyundai Genesis 2.0L Timing Chain Install: Tensioner Torque & Cover Sealant EM-29
  This is page EM-29 of a service manual section titled "Timing System," covering timing chain installation steps 5 through 8. Step 5 covers installing the timing chain tensioner arm (B) with a tightening torque of…
• Hyundai 2.0L CVVT Timing Chain Installation Procedure & Torque Specs (EM-28)
  This is page EM-28 from an Engine Mechanical System service manual section covering timing chain installation. The page presents a four-step installation procedure with supporting illustrations. Step 1 covers…
• Hyundai Genesis Coupe Valve Cover & Crank Pulley Install - Torque Specs EM-31
  This is page EM-31 of a Hyundai service manual section titled "Timing System," covering installation steps for the cylinder head cover (valve cover) and front engine accessories. Step 10 details installing the cylinder…
• Hyundai Genesis Coupe TPS Adaptation (Reset) Procedure After ETC/ECM Replacement
  This document is a service notice excerpt describing the Throttle Position Sensor (TPS) adaptation procedure that must be performed after replacing the Electronic Throttle Control (ETC) assembly or the Engine Control…
• Hyundai Genesis Coupe Heater Core Removal - Service Manual Page HA-36
  This is page HA-36 from a Hyundai factory service manual's Heating, Ventilation, Air Conditioning (HA) section, showing part of the heater core / heater unit disassembly procedure. The page contains steps 10 through 12…
• Hyundai Genesis Coupe Heater & Blower Unit Removal - Replacement Procedure
  This page is a service procedure titled "Replacement" describing the first nine steps for removing the heater and blower unit (heater core assembly) from the vehicle. The procedure begins with disconnecting the…
• 2010 Hyundai Genesis Coupe Connector MR01 Location - Driver A-Pillar Photo
  This document is a service manual reference photograph labeled "PHOTO.47" showing the location of connector MR01 in a vehicle's interior. The photo is taken from inside the cabin looking at the driver-side A-pillar…
• 2010 Hyundai Genesis Driver Door Component Locations - D05 D07 D08 JDDRI
  This document is a labeled photograph showing the interior of a driver-side door with the trim panel removed, exposing the inner door structure, wiring harness, and mounted components. Four callouts identify component…
• Hyundai Genesis Sunroof Motor Initialization & Emergency Handle Procedure
  This service procedure page covers sunroof adjustment and emergency operation. The first section, 'How To Initialize,' explains the sunroof motor initialization: verify the glass is installed and height adjustment is…
• Hyundai Genesis Rear Differential Cover & Drain/Fill Plug Torque Specs - DS-40
  This is page DS-40 from a service manual section titled "Driveshaft and axle," covering reassembly steps for a rear differential. Step 5 instructs applying liquid sealant to the differential carrier as shown in an…
• Hyundai Genesis Coupe Concentric Slave Cylinder (CSC) Removal & Air Bleeding
  This service manual page covers the removal, installation, and air bleeding (adjustment) procedure for the C.S.C (Concentric Slave Cylinder) on a manual transmission. Removal requires first removing the transmission…
• 2010 Hyundai Genesis V6 Alternator Removal Procedure - Service Manual EEA-20
  This page (EEA-20) from a Hyundai service manual's Engine Electrical System section covers the first six steps of the alternator replacement procedure. The steps instruct the technician to: (1) disconnect the battery…
• 2010 Hyundai Genesis Coupe Interior Fuse Box Rear Connectors I/P-A to I/P-K
  This document is a labeled photograph (PHOTO.49) from a service manual showing the rear (harness) side of an interior fuse box / junction block, viewed from under the dash area of the vehicle. Arrows identify the…
• 2010 Hyundai Genesis Coupe Heater Unit Component Location Diagram
  This is a single page from a service manual section titled "Heater Unit" showing the "Component Location" of the heater unit. The page consists of a line illustration of a two-door coupe body viewed from the front…
• Hyundai Genesis Coupe 2.0T G4KF Knock Sensor & Starter Connector Locations
  This document is a labeled photographic connector-location diagram titled "13. Left Side of Engine" for the G4KF engine (Hyundai's 2.0L turbo four-cylinder used in the Genesis Coupe). The photo shows the left side of…