Service Procedures — Ford Taurus 1996-1999

Technical Reference

Member-uploaded diagrams & documents for this generation. AI-classified; community-verified where badged.

Service Procedures

• Ford Pinpoint Test JF7-JF11: Coil Driver (CD) Circuit & Ignition Coil Diagnosis
  This document is one page of a Ford pinpoint diagnostic test procedure (steps JF7 through JF11) for troubleshooting the ignition coil driver (CD) circuit between the PCM and the ignition coils. Each step is laid out in…
• Ford Pinpoint Test JF4-JF6: Ignition Coil & Coil Driver Circuit Misfire Diagnosis
  This document is one page of a Ford pinpoint diagnostic test procedure covering steps JF4 through JF6 for diagnosing ignition coil and coil driver circuit problems related to engine misfire. Step JF4 (Check for Damaged…
• Ford Pinpoint Test JF1-JF3: Ignition Coil Not Firing Diagnosis (DTC P0350-P0360)
  This document is one page of a Ford pinpoint diagnostic test procedure (steps JF1 through JF3) for diagnosing an ignition coil that is not firing on an electronic ignition (EI) system controlled by the PCM. Step JF1…
• Ford AX4S Transaxle Pressure Test Port Locations Diagram - Line, EPC, Direct Clutch
  This document is a labeled line-art diagram of the Ford AX4S automatic transaxle, viewed from the case exterior, identifying the locations of its diagnostic pressure taps and fittings. Four callouts point to specific…
• Ford Taurus Front Subframe Plate Nut Removal Diagram - Access Hole & Tab
  This document is a single-page service illustration showing how to access and remove a front subframe plate nut on a vehicle. The main line drawing depicts the underbody/subframe area of the vehicle, viewed from below…
• Ford Valve Shim Removal with Compressed Air - Tappet Holder T96P-6500-AH Diagram
  This is a single-page illustration from a Ford service procedure showing how to remove a valve adjusting spacer (shim) using compressed air. The line drawing depicts a cylinder head with an overhead camshaft, on which…
• Ford Tappet Holder T96P-6500-AH & Compressor T89P-6500-A Placement Diagram
  This document is a single illustration from a service procedure showing the placement of special valvetrain service tools on an overhead-cam cylinder head. Two Ford special service tools are identified by callouts: the…
• Ford Tappet Compressor T89P-6500-A Placement Diagram - DOHC Valve Shim Service
  This is a single-page service illustration showing the placement of a valve tappet compressor tool during a valve adjustment procedure on a dual overhead cam (DOHC) engine. The line drawing depicts a technician's hand…
• Ford Valve Clearance Check Diagram - Feeler Gauge Between Cam Lobe & Tappet 6500
  This document is a single-page service illustration showing how to check valve clearance on an overhead-cam engine. The line drawing depicts a cam lobe positioned above a valve tappet, with a feeler gauge inserted…
• Ford Transmission Range (TR) Sensor Location & Alignment Tool T92P-70010-AH
  This document contains two service illustration diagrams related to the Transmission Range (TR) sensor on a Ford automatic transmission. The first illustration (figure ID AD0273-A) shows the location of the…
• 1997 Ford Taurus RAP Module Location Diagram (N13293-A) - Service Illustration
  This document is a single black-and-white line-art illustration (Ford illustration reference number N13293-A) showing the mounting location and installation of a module — per the uploader's filename, the RAP (Remote…
• Ford AX4N Transaxle EPC & Line Pressure Test Port Locations Diagram
  This document is a line-art illustration from a Ford service manual showing the location of the EPC (Electronic Pressure Control) and LINE pressure test ports on an AX4N automatic transaxle. The transaxle case is drawn…
• Ford Taurus Halfshaft ABS Sensor Ring Press Diagram – Tool 206-072
  This document is a single illustration from a Ford service procedure showing the installation (pressing) of the front brake anti-lock (ABS) sensor indicator ring onto a front wheel driveshaft joint (halfshaft outboard…
• Ford Taurus Front ABS Sensor Ring Remover/Replacer 206-072 - Halfshaft Service
  This document is a single service illustration showing the installation (or removal) of a front brake anti-lock sensor indicator ring, part reference 2C182, using a special service tool identified as the Front Sensor…
• Ford Taurus Halfshaft ABS Sensor Ring Press Install Diagram – Tool 206-072
  This document is a single illustration from a Ford service procedure showing how to install (press on) the front brake anti-lock sensor indicator ring onto a front wheel driveshaft joint. The line drawing depicts a…
• Ford Taurus Front ABS Sensor Ring Removal - Halfshaft CV Joint Tool 206-072
  This document is a single illustration from a Ford service procedure showing the installation or removal of an anti-lock brake sensor ring (tone ring) on a front halfshaft. The line drawing depicts a hand holding the…