SuperMotors SuperMotors SUPERMOTORS Search: try “orange Bronco on 35s”
Home/ Registry/ Ford/ Bronco/ 1980-1986/ “Erika”/ Photo supermotors.net/registry/media/117598

1985 Ford Bronco Rock Slider Blueprint - Side Profile Line Drawing

Side-profile line drawing of a fabricated rail or sill part
Side-profile line drawing of a fabricated rail or sill partOriginal file
Side-profile line drawing of a fabricated rail or sill part

Reference · 1980-1986 BroncoAll 26 blueprints

1985 Ford Bronco Radius Arm Bracket Fabrication Blueprint - Dimensions & Angles 1985 Ford Bronco Rock Slider Blueprint - Side Profile Line Drawing 1985 Ford Bronco Radius Arm Mount Blueprint Sketch - Bracket Diagram Trim panel hole layout photos for positions A, B and C with tape measure readings from the body line Ford Axle Brake Flange Dimensions Diagram - Small/Big Ford, Bronco, 8.8" Types Ford Bronco Clutch Lever Control Arm Blueprint - Hole Sizes & Dimensions 1984 Ford Bronco Rear Cross Sill End Detail - Dimensioned Repair Sketch 1984 Ford Bronco Rear Cross Sill End Detail - Hand-Drawn Fabrication Blueprint Ford Bronco Steering Box Clamp Brace Blueprint - Dimensions & Fab Drawing Ford Bronco Gas Tank Skid Plate Blueprint - Dimensions & Weld Details DIY Gas Tank Skid Plate Blueprint - 1/4" Steel Plans (1980 Ford Bronco) Ford 10-Cut Lock Cylinder & Key Diagram - Ignition Lock Set Part Numbers 26blueprints1980-1986 Ford Bronco More reference Nitto Mud Grappler size chart with tread depth, diameter, width, rim, load and revs per mileBrochure 1985 Ford Bronco Owner-Uploaded Schematic Sketch - Unlabeled Line DrawingSchematic 1996 Ford Bronco & F-Series Trailer Wiring Diagram - 7-Pin Connector PinoutWiring diagram Ford Bronco Ignition Timing Curve Table - RPM vs Vacuum Advance (12° Base)Spec plate 1992-96 Ford F-150/F-250/F-350 2WD Front Sway Bar Diagram & Part NumbersExploded parts 1992 Ford E4OD Transmission Fault Code Diagnosis Chart - DTC List & SymptomsService procedure 1996 Ford Bronco/F-Series Starting System - Section 03-06 ContentsManual page 1985 Ford Bronco Vacuum Hose Routing Diagram - EGR, TAB/TAD Solenoids, CanisterVacuum routing Bronco drive shaft torque limits table and special tool T74P-4635-CTorque spec '95 F150 fuse and relay chart with fuse panel layout, ATC and Maxi fuse amp tablesFuse chart

Orthographic line drawing showing the side profile of a fabricated rail/sill part.

Part of 1980-1986 Ford Bronco Blueprints

AI caption · Photo 199 of 1405

This document is an untitled, unlabeled line drawing uploaded as 'Rock Sliders 1.JPG' to a 1985 Ford Bronco gallery on SuperMotors.net. The drawing shows a side (or plan) view of what appears to be a rock slider: a long, flat rectangular base plate with a rounded tubular rail running parallel above it, attached by at least two short vertical support legs near the ends and possibly intermediate mounts near the middle. The rail ends curve down toward the base plate at both ends. There are no dimensions, measurements, text callouts, material specifications, part numbers, or vehicle applicability statements anywhere in the drawing. A reader can learn only the general shape and construction concept of the fabricated rock slider, a rub rail standing off a mounting plate, but cannot determine lengths, tube diameters, plate thickness, mounting hole locations, or fitment details from this sheet alone. Any association with the 1985 Ford Bronco comes solely from the uploader's gallery attribution, not from content within the drawing itself.

Is this accurate? Sign in to help verify it.

Frequently asked questions

What does this blueprint show?
It shows a simple side-profile line drawing of a rock slider: a flat base plate with a tubular rail above it, connected by short vertical supports, with the rail ends curving down toward the plate.
Are there any dimensions or measurements on this drawing?
No. The drawing contains no dimensions, measurements, or scale information of any kind.
Does the drawing list part numbers or materials?
No. There are no part numbers, material callouts, or text annotations visible anywhere on the drawing.
How is the rail attached to the base in the drawing?
The drawing shows the tubular rail connected to the flat base plate by short vertical supports, with what appear to be two additional narrow attachment points near the middle of the span.

Comments

No comments yet.

More 1980-1986 Broncos