What fuses power the turn signal and hazard circuit in this diagram?

Two 15A fuses in the fuse box, at positions 15 and 19, feeding wires W/G and Y through connector E40 pins 18 and 19.

What wire colors are used for the left and right turn signal circuits?

Green/red (G/R) is used for the left-side turn signals and green/yellow (G/Y) for the right side; black (B) wires provide grounds, and G and Y/W wires connect the switch to the relay at E59.

Where does the turn signal and hazard warning relay connect?

The turn signal and hazard warning relay connects at connector E59, pins 1 and 3, with pin 2 going to ground via a black (B) wire.

Which connectors are used for the front and rear turn signal lights?

Front turn signal lights use connectors E27 (LH) and E04 (RH); rear turn signal lights use L18 (LH) and M01 (RH), each grounding at pin 5 with a black wire.

What do the numbered legend boxes [1]-[4] mean on this diagram?

They indicate build variants: [1] 2-DOOR-CAMI, [2] 2-DOOR-IWATA and 4-DOOR, [3] IWATA, [4] CAMI.

Home/ Registry/ Suzuki/ Samurai/ 1986-1995/ “Little Blue”/ Photo supermotors.net/registry/media/420661

Suzuki Turn Signal & Hazard Flasher Wiring Diagram - Fuses, Relay, Wire Colors

Wiring diagram: turn signal switch, hazard warning switch, front and rear turn signal lights and relay

‹ ›

Reference · 1986-1995 SamuraiAll 73 wiring diagrams

Suzuki Samurai Headlight & DRL Control Unit Wiring Diagram - Fuses, Switches

Suzuki Samurai Headlamp Wiring Diagram - Fuses 11/12 15A, Dimmer & Lighting Switch

Suzuki Turn Signal & Hazard Warning Wiring Diagram - Flasher Relay Circuit

Suzuki Turn Signal & Hazard Flasher Wiring Diagram - Fuses, Relay, Wire Colors

Suzuki Samurai EFI Wiring Diagram - EGR/EVAP Solenoids, Clutch & Shift Switch

Suzuki EFI Wiring Diagram - ECM, TPS, Injectors, IAC Valve & Temp Sensors

Suzuki Samurai EFI Wiring Diagram - Fuel Pump Relay, ECM, MAF & TCC Circuits

Suzuki Samurai 8v EFI Swap ECM Connector C2 Pinout - Wire Colors & Circuits

Suzuki Sidekick/Geo Tracker 8v EFI Swap into Samurai - ECM C1 Pinout & Wiring

73wiring diagrams1986-1995 Suzuki Samurai More reference

Schematic

1986 Suzuki Samurai Fuse Box Diagram - Main Fuse Block & Fuse Panel Layout

Fuse chart

Tatou 4S ATV Track System Rear Frame Dimensions & Specs Diagram

Brochure

Suzuki Samurai 8v EFI Swap Wiring - Pin Colors & 8A-20 Diagram Index (Pg 4)

Manual page

Suzuki Samurai Mitsubishi 12V Starter Data Plate - M3T41781 / 31100-83030

Spec plate

Vacuum routing

1987 Suzuki Samurai Fabrication Template - Hand-Drawn Full-Size Layout w/ Dims

Blueprint

Photo of Purple Compact Car Front Wheel & Fender (Misfiled Samurai Doc Scan)

Exploded parts

Trail Tough Samurai Twisted T/T shift shaft installation instructions beside bagged shift shafts and gasket

Service procedure

Wiring diagram of the turn signal and hazard warning system showing the switches, relay and front and rear turn signal lights.

Part of 1986-1995 Suzuki Samurai Wiring Diagrams

AI caption August 2006 · Photo 30 of 86

This document is a wiring diagram for the turn signal and hazard warning light circuit of a Suzuki vehicle. Power comes from two 15A fuses (positions 15 and 19) in the fuse box, feeding through wires W/G and Y (connector E40, pins 18 and 19) to the hazard warning switch and turn signal switch (LH/OFF/RH). The turn signal and hazard warning relay connects at connector E59 (pins 1, 3, 2). Green/red (G/R) wiring runs the left-side circuit and green/yellow (G/Y) the right-side circuit, feeding the front turn signal lights (connectors E27 LH and E04 RH), the combination meter turn indicators (TURN(LH), TURN(RH) via connectors G11/G09), and the rear turn signal lights (connectors L18 LH and M01 RH), with intermediate connectors E38/G05, G02/L02, L16/M07 and G06/E37. All lamps ground through black (B) wires to numbered chassis ground points (1, 6, 9, 10, 11). A legend distinguishes wiring variations by build: [1] 2-door CAMI, [2] 2-door IWATA and 4-door, [3] IWATA, [4] CAMI. The diagram lets a reader trace flasher circuit wiring, connector pin numbers, wire colors, and fuse ratings for diagnosing turn signal or hazard light faults.

Is this accurate? Sign in to help verify it.

Frequently asked questions

What fuses power the turn signal and hazard circuit in this diagram?: Two 15A fuses in the fuse box, at positions 15 and 19, feeding wires W/G and Y through connector E40 pins 18 and 19.
What wire colors are used for the left and right turn signal circuits?: Green/red (G/R) is used for the left-side turn signals and green/yellow (G/Y) for the right side; black (B) wires provide grounds, and G and Y/W wires connect the switch to the relay at E59.
Where does the turn signal and hazard warning relay connect?: The turn signal and hazard warning relay connects at connector E59, pins 1 and 3, with pin 2 going to ground via a black (B) wire.
Which connectors are used for the front and rear turn signal lights?: Front turn signal lights use connectors E27 (LH) and E04 (RH); rear turn signal lights use L18 (LH) and M01 (RH), each grounding at pin 5 with a black wire.
What do the numbered legend boxes [1]-[4] mean on this diagram?: They indicate build variants: [1] 2-DOOR-CAMI, [2] 2-DOOR-IWATA and 4-DOOR, [3] IWATA, [4] CAMI.