What engines does this belt routing diagram apply to?

The decal states it is for 5.0L and 5.8L engine drive belt installation ('5.0L & 5.8L DRIVE BELT INSTALLATION / MOTEUR 5 L OU 5,8 L').

How do you relieve serpentine belt tension according to this decal?

Lift counterclockwise using the idler (tensioner) pulley bolt to relieve tension, as shown by the wrench illustration at the top of the decal.

What pulleys does the serpentine belt route around?

The alternator, tensioner, fan, A/C compressor or idler pulley, power steering pump, air pump, and crankshaft.

Does this diagram cover engines without A/C?

Yes: one pulley is labeled 'A/C OR IDLER', indicating an idler pulley occupies that position on non-A/C vehicles.

Home/ Registry/ Ford/ Bronco/ 1987-1991/ 1989 Ford Bronco/ Photo supermotors.net/registry/media/222433

Ford 5.0L & 5.8L Serpentine Belt Routing Diagram Decal - Bronco/F-Series

Underhood decal showing 5.0L/5.8L serpentine drive belt routing diagram

‹ ›

Reference · 1987-1991 BroncoAll 110 schematics

1989 Ford Bronco Brake Line Routing Sketch - Master Cylinder & Proportioning Valve

1989 Ford Bronco Brake Line Routing Sketch - Master Cylinder to Calipers & Rear

Ford 5.0L & 5.8L Serpentine Belt Routing Diagram Decal - Bronco/F-Series

Ford 5.0 Fox Mustang Short Belt Routing Diagram - 84.5" & 70.5" vs Stock

Ford Thermactor Air Bypass Valve Cutaway Diagram - Port Identification

Ford Vacuum Check Valve Direction Diagram - Airflow & Black Vacuum Side

Ford Thermactor Air Diverter Valve Diagram - Inlet & Outlet Port Identification

Ford Idle Air Control (IAC) Valve Diagram - Cutaway Schematic & Airflow

Ford Idle Air Bypass (IAB) Solenoid Cutaway Diagram - Plunger, Spring, Airflow

Ford Idle Air Control (ISC-BPA) Solenoid Cutaway Schematic - Bronco IAC Valve

Ford TPS Throttle Position Sensor Wiring Diagram - VREF, TP SIG, SIG RTN Colors

Integral Gear Power Steering Fluid Flow Diagram - Ford Bronco Gear Box Schematic

110schematics1987-1991 Ford Bronco More reference

Wiring diagram

Ford Canister Purge Regulator Valve (CANP 9C915) Test Procedure - Figure 11

Service procedure

Welder Input Data Plate - Serial JH229505, Stock 901782, 200/230/460V Specs

Spec plate

Ford 5.0L V8 PCV Valve & Hose Routing Diagram - 9A474, 6B890, 6A664

Exploded parts

Ford 5.0L/5.8L Air Throttle Body Assembly Diagram - Canister Purge Ports & TPS

Manual page

Brochure

Blueprint

'89 Ford vehicle emission control information label with EEC IV/EFI timing steps and vacuum hose routing

Vacuum routing

1990 Ford Bronco Fuse Panel Diagram: Fuse Positions, Amps & Circuits (11-2)

Fuse chart

Ford V8 Intake Manifold Bolt Tightening Sequence Diagram - Stud Locations

Torque spec

Underhood decal showing serpentine drive belt routing for 5.0L and 5.8L engines with labeled pulleys.

Part of 1987-1991 Ford Bronco Schematics

AI caption July 2005 · Photo 12 of 25

This document is a scan of a factory underhood serpentine drive belt routing decal for Ford 5.0L and 5.8L V8 engines, printed in both English and French. It shows a schematic diagram of the accessory drive belt path around seven pulleys: alternator (ALT.), belt tensioner (TENSIONER/TENDEUR), fan (FAN/VENTILATEUR), A/C compressor or idler pulley (A/C OR IDLER / CLIM. OU POULIE FOLLE), power steering pump (P/S / DIR.), air pump (AIR PUMP / POMPE À AIR), and crankshaft (CRANKSHAFT / VILEBREQUIN). An illustration with a red arrow at the top shows a hand with a wrench on the tensioner, with instructions to lift counterclockwise using the idler pulley bolt to relieve belt tension when installing or removing the belt. The decal is titled '5.0L & 5.8L DRIVE BELT INSTALLATION' (Parcours de la courroie, Moteur 5 L ou 5,8 L). A Ford part number, E87TA-8B658-BA, is printed vertically along the right edge. A reader can learn the correct serpentine belt routing for an air-pump-equipped 5.0/5.8 engine and the correct method for releasing tensioner pressure during belt replacement.

Is this accurate? Sign in to help verify it.

Frequently asked questions

What engines does this belt routing diagram apply to?: The decal states it is for 5.0L and 5.8L engine drive belt installation ('5.0L & 5.8L DRIVE BELT INSTALLATION / MOTEUR 5 L OU 5,8 L').
How do you relieve serpentine belt tension according to this decal?: Lift counterclockwise using the idler (tensioner) pulley bolt to relieve tension, as shown by the wrench illustration at the top of the decal.
What pulleys does the serpentine belt route around?: The alternator, tensioner, fan, A/C compressor or idler pulley, power steering pump, air pump, and crankshaft.
Is there a part number on this decal?: Yes, E87TA-8B658-BA is printed vertically along the right edge of the label.
Does this diagram cover engines without A/C?: Yes: one pulley is labeled 'A/C OR IDLER', indicating an idler pulley occupies that position on non-A/C vehicles.