Where is the VIN located on the Ford 6.9L V-8 diesel engine?

Per Fig. 1, the Vehicle Identification Number is stamped on the engine block on the right side of the engine, toward the front/upper area as shown by the callout arrow.

Where is the emissions decal on the 6.9L diesel?

The Vehicle Emission Control Information Decal (VECI) is located on the right side of the engine, indicated in Fig. 1 near the upper rear area of the engine.

Which vehicles does this 6.9L diesel figure apply to?

The figure caption states 'F-150: F-250 Shown, E-150, E-350 Similar,' so it applies to Ford F-Series trucks and E-Series vans with the 6.9L diesel.

What is the oil pump output for the 6.9L diesel?

The text states oil pump flow is 45.4 liters (12 gallons) per minute at rated speed at a pressure of 483 kPa (70 psi).

At what temperature does the 6.9L diesel thermostat begin to open?

The text indicates the thermostat begins to open at approximately 192°F, after which coolant is allowed to return to the radiator.

Home/ Registry/ Ford/ Bronco/ 1980-1986/ 1986 Ford Bronco/ Photo supermotors.net/registry/media/491610

Ford 6.9L V-8 Diesel Engine Right Side Diagram - VIN & VECI Decal Location

Scanned manual page with 6.9L V-8 diesel engine diagram and labels

‹ ›

Reference · 1980-1986 BroncoAll 32 manual pages

Speed control manual page 137 with circuit description and component location table

Ford 6.9L V-8 Diesel Engine Right Side Diagram - VIN & VECI Decal Location

Spring rate table in Spanish comparing K constant lb/pulg, wire diameter, coil count and spring diameter

Ford 300 Inline Six Manifold Removal/Install & Bolt Torque Sequence - Manual Pg 71

Ford 300 Inline Six Engine Exploded View & Flywheel Removal - Manual Page 73

Ford Bronco Carburetor Choke Cap & Fuel Line Replacement - Manual Page 156

Ford 7200 VV Variable Venturi Carburetor Diagram - Component Callouts (Manual Pg 150)

YFA 1-V Carburetor Diagrams - Feedback & Non-Feedback, Inline Six (Ford Bronco)

Ford 3G Alternator Output Curves - 95/130 Amp, Leece-Neville 165A, Mitsubishi 215A

AirSensors TBI Fuel Flow Path Diagram - EFI Fuel System Component Layout

Ford Transmission Pan Identification Chart - C4, C5, C6, AOD, E4OD, 4R70W

Ford Bronco/F-Series Fuel & Exhaust Systems - Haynes Ch. 4 Specs & Torque

32manual pages1980-1986 Ford Bronco More reference

Wiring diagram

1986 Ford Bronco Speed Control Amplifier & Wiring Harness Diagram (14401, 9A840)

Exploded parts

1984 Ford Bronco Owner Guide, Operating Guide & 4-Wheeling With Ford Booklets

Brochure

Ford Bronco Ignition Timing Curve Table - RPM vs Vacuum Advance (12° Base)

Spec plate

Ford Bronco Sliding Caliper Pin Installation Diagram - Brake Grease & Pin Tabs

Service procedure

Schematic

Ford Axle Brake Flange Dimensions Diagram - Small/Big Ford, Bronco, 8.8" Types

Blueprint

1985 Ford Bronco Vacuum Hose Routing Diagram - EGR, TAB/TAD Solenoids, Canister

Vacuum routing

Torque spec

1982-83 Ford Bronco Fuse Box Cover Diagram - Fuse Positions & Amp Ratings

Fuse chart

Scanned service manual page showing a 6.9L V-8 diesel engine with labeled VIN and emission-decal locations.

Part of 1980-1986 Ford Bronco Manual Pages

AI caption March 2007 · Photo 62 of 239

This is page 22-08-3 from a Ford shop/service manual section covering the 6.9L V-8 diesel engine. The dominant feature is a large line-art illustration labeled 'FIG. 1 6.9L Diesel: Right Side, F-150, F-250 Shown, E-150, E-350 Similar' (illustration reference A7407-2B), showing the right side of the engine with the flywheel/flexplate visible. Two callouts identify the locations of the Vehicle Identification Number stamping on the block and the Vehicle Emission Control Information (VECI) decal. Surrounding body text, only partially legible due to lighting and page curvature, describes fuel system operation (fuel metered by the injection pump and delivered under high pressure through injection lines to nozzles that atomize fuel for combustion), coolant flow through the crankcase and cylinder heads with thermostat and heater-core bypass behavior (thermostat begins opening around 192°F), and the lubrication system (oil pump flow of 45.4 liters / 12 gallons per minute at rated speed and a pressure of 483 kPa / 70 psi). Readers can learn where to find the VIN and VECI decal on the 6.9L diesel and gain general descriptions of its fuel, cooling, and lubrication systems as applied to Ford F-150-F-250 and E-150-E-350 trucks/vans.

Is this accurate? Sign in to help verify it.

Frequently asked questions

Where is the VIN located on the Ford 6.9L V-8 diesel engine?: Per Fig. 1, the Vehicle Identification Number is stamped on the engine block on the right side of the engine, toward the front/upper area as shown by the callout arrow.
Where is the emissions decal on the 6.9L diesel?: The Vehicle Emission Control Information Decal (VECI) is located on the right side of the engine, indicated in Fig. 1 near the upper rear area of the engine.
Which vehicles does this 6.9L diesel figure apply to?: The figure caption states 'F-150: F-250 Shown, E-150, E-350 Similar,' so it applies to Ford F-Series trucks and E-Series vans with the 6.9L diesel.
What is the oil pump output for the 6.9L diesel?: The text states oil pump flow is 45.4 liters (12 gallons) per minute at rated speed at a pressure of 483 kPa (70 psi).
At what temperature does the 6.9L diesel thermostat begin to open?: The text indicates the thermostat begins to open at approximately 192°F, after which coolant is allowed to return to the radiator.