What engine does this component location view cover?

The 7.3 DI diesel engine; the caption states '7.3 DI DIESEL ENGINE (2 OF 2)' for the 1994 Bronco/F-Series.

Where is the glow plug relay shown on this diagram?

Connectors C1002 and C1004 for the glow plug relay are called out near the top left of the engine compartment illustration.

What connector number is the Powertrain Control Module (PCM)?

C1027 is labeled as the Powertrain Control Module (PCM), located on the right side of the engine compartment.

Which connector is the Injector Driver Module (IDM)?

C128 is labeled as the Injector Driver Module (IDM) on the right side of the diagram.

What is the ICP sensor connector number?

C146 is the Injection Control Pressure (ICP) sensor connector, shown near the top center of the engine view.

Home/ Registry/ Ford/ Bronco/ 1992-1996/ 1996 Ford Bronco/ Photo supermotors.net/registry/media/1112033

1994 Ford Bronco/F-Series 7.3 Diesel Component Location Diagram - EVTM 151-12

1994 Ford Bronco/F-Series 7.3L DI diesel component location views, section 151-12, glow plug and injector parts

‹ ›

1994 Bronco/F-Series 7.3L DI diesel component location view (151-12, 2 of 2) mapping glow plug relay, injector driver module, PCM, IPR, blower motor and fuel/sensor parts on a grid.

AI caption July 2017 · Photo 317 of 413

This is page 151-12 of the 1994 Ford Bronco/F-Series Electrical and Vacuum Troubleshooting Manual (EVTM), titled 'Component Location Views.' It presents an underhood illustration (view 2 of 2) of the 7.3L DI diesel engine compartment, overlaid with a lettered/numbered locator grid (columns 1-10, rows A-F). Callout lines identify the physical locations of electrical connectors, sensors, switches, and grounds, including the glow plug relay (C1002, C1004), plugged fuel filter switch (C1015), injection control pressure (ICP) sensor (C146), brake pressure switch (C102), powertrain control module (C1027 PCM), injector driver module (C128 IDM), low vacuum warning switch (C1010), oil pressure switch (C135), fuel water switch (C1001), injection pressure regulator (C156 IPR), A/C clutch field coil (C163), water-in-fuel sensor (C1056), blower motor (C168) and resistor (C169), A/C clutch cycling pressure switch (C162), windshield washer pump motor (C1030), park/turn and side marker lamps (C1031, C1032, C1052-C1055), grounds G100 and G101, and unlabeled connectors C1057, C1058, C1060, C138, C202. The sheet is identified as FPS-12129-94, sheet 12 of 24, and includes a note not to use the grid for reporting repair locations and a front-of-vehicle direction arrow.

This document covers 1994, which may differ from this 1996 Ford Bronco.

Is this accurate? Sign in to help verify it.

Frequently asked questions

What engine does this component location view cover?: The 7.3 DI diesel engine; the caption states '7.3 DI DIESEL ENGINE (2 OF 2)' for the 1994 Bronco/F-Series.
Where is the glow plug relay shown on this diagram?: Connectors C1002 and C1004 for the glow plug relay are called out near the top left of the engine compartment illustration.
What connector number is the Powertrain Control Module (PCM)?: C1027 is labeled as the Powertrain Control Module (PCM), located on the right side of the engine compartment.
Which connector is the Injector Driver Module (IDM)?: C128 is labeled as the Injector Driver Module (IDM) on the right side of the diagram.
What is the ICP sensor connector number?: C146 is the Injection Control Pressure (ICP) sensor connector, shown near the top center of the engine view.