Service Procedures: Nissan Micra 1983-1992

Technical Reference

Member-uploaded diagrams & documents for this generation. AI-classified; community-verified where badged.

Service Procedures

• Nissan Micra Wiring Harness Layout Diagram: Outline (EL-61, SEL400G)
  This document is a single page (EL-61) from a Nissan factory service manual's Electrical (EL) section, titled "HARNESS LAYOUT: Outline." It contains an isometric line drawing of a 3-door hatchback vehicle with the body…
• Nissan Micra Electrical Units Location - Passenger Compartment Relays & Fuse Block
  This is a scanned page (EL-60) from a Nissan factory service manual, from the Electrical (EL) section, titled "Location of Electrical Units: Passenger Compartment." It uses an overview drawing of the dashboard with…
• 1990 Nissan Micra Passenger Compartment Electrical Unit Locations (EL-60)
  This is a scanned page (EL-60) from a Nissan service manual, in the electrical section, titled 'Location of Electrical Units: Passenger Compartment.' It shows an overview drawing of the instrument panel/dashboard with…
• Nissan Micra Radio Antenna Trimmer Adjustment & Antenna Removal (EL-58)
  This service manual page (EL-58) from the RADIO section covers two procedures: Antenna Trimmer Adjustment and Antenna Removal. The trimmer adjustment section explains that adjustment is needed when there is fading or…
• Nissan Wiper & Washer Adjustment, Intermittent Amplifier Check (EL-53)
  This is page EL-53 of a Nissan service manual covering wiper and washer service procedures. The left column details front windshield wiper adjustment: setting the wiper switch to LOW then OFF (Auto Stop) before arm…
• 1990 Nissan Micra Fuel Tank Gauge Unit Check & Speedometer Cable Removal EL-48
  This page (EL-48) from the 'Meter and Gauges' section of a factory service manual covers two procedures. The left side shows the Fuel Tank Gauge Unit Check: an illustrated diagram of the fuel sender unit with float arm…
• Nissan Micra Combination Switch Replacement - Lighting, Wiper & Hazard (EL-39)
  This page is a service procedure from a factory service manual (page EL-39, electrical section) covering replacement of the combination switch, the multi-function stalk switch assembly on the steering column. The text…
• Nissan Micra Distributor Pick-up Coil & Governor Advance Check - EL-36
  This is page EL-36 from a Nissan service manual, covering the Ignition System, Distributor section. It provides two brief inspection procedures. First, 'Checking Governor Advance' instructs the technician to remove the…
• Nissan Micra Distributor Test: Ignition Coil Resistance & Vacuum Advance Check
  This is page EL-35 from a Nissan factory service manual covering the ignition system distributor. It provides three inspection procedures. First, Ignition Coil Resistance: using an ohmmeter, measure primary winding…
• Nissan Micra Ignition System Troubleshooting Flowchart - No Start & Spark Test
  This is a scanned service manual page covering ignition system trouble-shooting, uploaded to a 1990 Nissan Micra document album. The page presents a diagnostic flowchart for two symptoms: "Engine turns erratically" and…
• Nissan Micra Alternator Diode Check & Reassembly - Service Manual Page EL-28
  This is page EL-28 from a factory service manual's Electrical (EL) section covering the Charging System, Alternator. The left column continues the alternator Diode Check procedure, showing illustrated conduction tests…
• Nissan Micra Alternator Stator & Diode Check - Continuity Test Procedure
  This is page EL-27 of a factory service manual covering the charging system (alternator), specifically the Stator Check and Diode Check procedures. The stator check requires unsoldering the connecting wires to separate…
• Nissan Charging System Troubleshooting Flowchart - IC Regulator Alternator EL-24
  This is page EL-24 of a Nissan service manual covering charging system trouble-shooting for alternators with an IC regulator. It states prerequisites for testing: a fully charged battery, a 30-volt voltmeter, and…
• Nissan Micra Starter Armature Check - Commutator & Mica Specs (EL-20)
  This is page EL-20 from a Nissan service manual covering the Starting System (Starter), specifically the Armature Check procedure. It describes five inspection steps for a starter motor armature: (1) a continuity test…
• Nissan Micra Starter Brush & Field Coil Check - Service Manual Page EL-19
  This is page EL-19 from a Nissan factory service manual covering the Starting System (Starter), uploaded to a 1990 Nissan Micra gallery. The page details two inspection procedures: Brush Check and Field Coil Check. The…
• 1990 Nissan Micra HVAC Door Control Cable Adjustment - Intake, Temp & Air Cables
  This page is from a service manual section titled "DOOR CONTROL: Control Cable Adjustment (Cont'd)" (page HA-5), covering the heater/ventilation (HVAC) control cable adjustment procedure. It instructs the technician to…
• Nissan Micra Heater Control Removal & Cable Adjustment - Service Manual HA-4
  This is page HA-4 of a factory service manual section titled "DOOR CONTROL," covering heater (HVAC) door control service procedures. The left column, "Heater Control Removal," explains removal of the heater control…
• Nissan Micra Exterior Body Seals & Weatherstrips - Service Manual Page BF-16
  This is page BF-16 from a Nissan service manual body (BF) section, titled "Interior and Exterior: Exterior (Cont'd)." It is a service/reference page consisting of exploded and cross-section illustrations for exterior…
• Nissan Wagon Exterior Molding & Weatherstrip Installation - Service Manual BF-14
  This is page BF-14 of a factory body (BF) service manual section titled "Interior and Exterior: Exterior." It covers installation of exterior moldings and weatherstrips on a wagon-body vehicle. Two exploded body…
• Nissan Micra Floor Trim: Floor Mat & Luggage Mat Installation Diagram (BF-13)
  This page is from a factory service manual section titled "Interior and Exterior: Interior (Cont'd)" covering FLOOR TRIM, page BF-13. It contains two labeled illustrations. The first, "Floor mat" (figure SBF406C)…
• Nissan Micra Roof Trim & Headlining Installation - Service Manual Page BF-12
  This is a single page (BF-12) from a Nissan factory service manual section titled "Interior and Exterior," continuing the "Interior" subsection with the procedure "Roof Trim Installation." The page contains two labeled…
• Nissan Micra Rear Door Removal & Adjustment - Glass, Handle, Lock Striker (BF-8)
  This is page BF-8 from a factory service manual section titled "BODY END AND DOOR," covering the rear door. It begins with two cautions: avoid scratching the vehicle body when removing the door, and check door lock…
• Nissan Micra Back Door Opener & Front Door Adjustment - Torque Specs (BF-7)
  This is page BF-7 of a Nissan factory service manual section titled "BODY END AND DOOR." The top half covers the Back Door Opener, cautioning not to bend the opener cable with excessive force. It shows the opener…
• Nissan Back Door & Rear Bumper Adjustment, Torque Specs - BF-6 Service Manual
  This is a scanned page (BF-6) from a Nissan factory service manual, section "Body End and Door: Rear End," covering back door (rear hatch/tailgate) and rear bumper service. It gives adjustment instructions: adjust the…
• Nissan Micra Front End Body Service - Hood, Grille & Bumper Torque Specs (BF-5)
  This is page BF-5 from a Nissan factory service manual section titled "BODY END AND DOOR," covering front end body service. General precautions instruct placing padding on hood corners when removing/installing the hood…
• Nissan R22T Manual Steering Gear Boot Clamp Assembly & Adjustment (ST-11)
  This is one page (ST-11) from a Nissan factory service manual covering the manual steering gear and linkage, model R22T, in the section 'Assembly and Adjustment (Cont'd)'. The page provides three illustrated boot clamp…
• Nissan R22T Manual Steering Gear Tie-Rod & Boot Assembly - Service Manual ST-10
  This is page ST-10 of a Nissan service manual covering assembly and adjustment of the R22T manual steering gear and linkage. It concludes a pinion adjustment step (readjust if pinion rotating torque is out of…
• Nissan R22T Manual Steering Gear Assembly & Pinion Torque Adjustment (ST-9)
  This is a page from a Nissan service manual covering assembly and adjustment of the R22T manual steering gear (rack and pinion) and linkage, page ST-9. It continues the assembly procedure: step 5 covers installing the…
• Nissan R22T Manual Steering Gear Inspection & Assembly - Service Manual ST-8
  This is page ST-8 from a Nissan factory service manual covering the manual steering gear and linkage, type R22T. The left column continues the Inspection section, giving specifications for checking the tie-rod ball…
• Nissan Micra Steering Wheel, Lock & Lower Joint Removal/Installation - ST-32
  This service manual page covers removal and installation of the steering wheel, steering lock, and steering lower joint. For the steering wheel, it instructs removal using special tool ST27180001 (J25726-A)…
• Nissan Front Disc Brake CL16 Caliper - Disassembly, Inspection & Assembly
  This is page BR-10 from a Nissan factory service manual covering the front disc brake caliper, type CL16. The page details three procedures: Disassembly, Assembly, and Inspection. For disassembly, the brake hose is…
• Nissan Micra Brake Booster Check, Removal & Inspection - Service Manual BR-8
  This is page BR-8 of a Nissan factory service manual covering the brake booster. It provides four procedures: an Operating Check (depress the pedal several times with the engine off to verify no change in stroke, then…
• Nissan Micra Brake Hydraulic Line Removal, Installation & Inspection (BR-4)
  This is page BR-4 of a Nissan factory service manual covering the brake hydraulic line, divided into two sections: Removal and Installation, and Inspection. The removal/installation section lists cautions: use the…
• Nissan Micra Brake Bleeding Procedure - Master Cylinder & Caliper Hydraulic System
  This is page BR-3 of a factory service manual section titled "Bleeding Hydraulic System: Bleeding Procedure." It provides step-by-step instructions for bleeding air from a diagonally-split brake hydraulic system…
• Nissan Micra Rear Suspension Shock Absorber Removal & Installation - RA-6
  This is page RA-6 from a factory-style service manual section titled "Rear Suspension." It documents the removal, inspection, and installation procedure for the rear shock absorber/coil spring assembly. Removal steps…
• Nissan Rear Axle Wheel Bearing Preload Adjustment - Torque Specs (RA-4)
  This is page RA-4 from a Nissan factory service manual, covering the Rear Axle (RA) section, specifically the continuation of the wheel bearing Preload Adjustment procedure. It provides steps 7 through 10: installing…
• Nissan Micra Rear Axle: Hub Bearing Installation & Preload Adjustment (RA-3)
  This is page RA-3 of a factory service manual section covering the REAR AXLE, uploaded as part of a Nissan Micra manual set. The left column details rear hub Installation: installing bearing outer races into the hub…
• Nissan Micra Front Suspension - Coil Spring Install & Transverse Link Inspection
  This page (FA-12) from a Nissan front suspension service manual section covers two topics. The left column continues 'Spring and Strut' with the ASSEMBLY step: when installing the upper and lower ends of the coil…
• Nissan Micra Front Axle Drive Shaft Disassembly & Inspection - FA-9 Service Manual
  This page (FA-9) from a Nissan service manual covers Front Axle, Drive Shaft procedures, continuing the disassembly instructions and providing inspection criteria. The disassembly section instructs removing the snap…
• Nissan Micra Front Axle Wheel Bearing Preload & Drive Shaft Installation FA-7
  This is page FA-7 from a Nissan factory service manual section covering the Front Axle, Wheel Hub and Knuckle. The left column concludes the Assembly and Adjustment procedure: step 8 details measuring wheel bearing…
• Nissan Micra Automatic Transaxle Stall Test Procedure - AT-65 Service Manual
  This is page AT-65 from an automatic transaxle (AT) service manual section titled "Trouble-Shooting and Diagnoses," covering the Stall Testing procedure. It explains that a stall test checks clutch and band holding…
• Nissan Micra Automatic Transaxle Assembly - Torque Converter Install (AT-54)
  This is a single page (AT-54) from a factory service manual's Automatic Transaxle (AT) section, covering the final steps (41-48) of the transaxle assembly procedure. It instructs the technician to inspect the torque…
• Nissan Micra Auto Transaxle Assembly AT-51: Output Shaft Shim Chart & Housing
  This is page AT-51 from a Nissan automatic transaxle (AT section) service manual, covering part of the transmission assembly procedure. It includes step 6 instructions for using a feeler gauge measurement with an…
• Nissan Automatic Transmission Assembly - Output Shaft End Play Adjustment
  This scanned service manual page, headed "ASSEMBLY," documents part of an automatic transmission assembly procedure, specifically step 24, adjusting output shaft end play after setting output shaft bearing preload. The…
• Nissan Micra Transmission Assembly - Output Shaft & Idler Bearing Preload
  This is a page from a factory service manual covering automatic transmission (transaxle) assembly procedures, specifically steps 22 and 23. Step 22 explains that if the transmission case, output shaft, tapered roller…
• Nissan Micra Automatic Transaxle Assembly Steps 16-21 - Governor Shaft Torque
  This page is from a service manual's automatic transaxle ASSEMBLY section, covering steps 16 through 21 of reassembly. Step 16 describes installing the one-way clutch together with the rear carrier by turning the rear…
• Nissan Automatic Transmission Assembly AT-47: Low & Reverse Brake Clearance
  This is page AT-47 of an automatic transmission section from a factory service manual, covering steps 10 through 15 of the transmission assembly procedure. Step 10 covers installing the shell and sun gear assembly with…
• Nissan Automatic Transaxle Diff Side Bearing Preload Adjustment (AT-42)
  This is page AT-42 from a Nissan automatic transaxle service manual covering "Diff. Side Bearing Preload Adjustment." It continues the Type A procedure (steps 10-13): installing the bearing retainer to the transmission…
• Nissan Micra Automatic Transaxle Diff Side Bearing Preload Adjustment (AT-41)
  This is page AT-41 of an automatic transaxle service manual section covering differential side bearing preload adjustment. It explains that whenever the transmission case, bearing retainer, tapered roller bearing…
• Nissan Micra AT Final Drive Differential Assembly Procedure - Page AT-40
  This is page AT-40 of a Nissan factory service manual, from the Automatic Transaxle (AT) section under "Repair for Component Parts: Final Drive (Cont'd)". It covers the ASSEMBLY procedure for the final drive…
• Nissan AT Final Drive Disassembly & Side Gear Clearance Spec (AT-39)
  This is page AT-39 from a Nissan service manual, covering the 'Repair for Component Parts: Final Drive' section within the Automatic Transaxle (AT) chapter. It details disassembly and inspection procedures for the…
• Nissan A/T Bearing Retainer Assembly - Seal, O-Ring & Inner Race (AT-38)
  This is page AT-38 from a factory-style automatic transmission (A/T) service manual section titled 'Repair for Component Parts', covering the assembly of the bearing retainer (continued from a previous page). The page…
• Nissan Micra Automatic Transaxle Disassembly Steps 15-21 - Service Manual AT-18
  This is page AT-18 from a factory service manual's automatic transaxle Disassembly section, uploaded to a 1990 Nissan Micra gallery. It covers steps 15 through 21 of the disassembly procedure. Step 15 instructs…
• Nissan Micra Automatic Transaxle Disassembly Steps 1-6 - Service Manual AT-16
  This page is from an automatic transaxle service manual section (page AT-16) covering the beginning of the transaxle disassembly procedure. It lists six numbered steps: (1) drain transaxle fluid, (2) remove torque…
• Nissan Micra Automatic Transaxle Removal & Installation - Service Manual AT-12
  This is page AT-12 from a factory service manual's Automatic Transaxle (AT) section, covering "Removal and Installation" of the automatic transaxle. The Removal column shows a diagram (SAT469) of the vehicle supported…
• Nissan Micra Automatic Transaxle Removal & Installation - Service Manual AT-12
  This is page AT-12 of a factory service manual section covering removal and installation of an automatic transaxle (A/T). The Removal side instructs disconnecting the drive shafts (referencing Section FA), removing the…
• Nissan Micra Automatic Transaxle Governor Shaft & Inhibitor Switch Adjustment AT-10
  This is page AT-10 from a Nissan factory service manual's Automatic Transaxle (AT) section, covering "On-Vehicle Service" procedures. The left column details governor shaft removal: remove the governor cap, remove the…
• Nissan Micra Manual Transmission Reassembly Steps 14-20 - MT-25 Turning Torque
  This is page MT-25 from a Nissan factory service manual, covering the final steps (14-20) of manual transmission reassembly. Step 14 shows installation of the reverse bracket assembly and guide plate (illustration…
• Nissan Micra Manual Transmission Reassembly Steps 8-13 - Service Manual MT-24
  This is page MT-24 from a factory service manual's Manual Transmission (MT) section, covering steps 8 through 13 of the transaxle reassembly procedure. Step 8 instructs the technician to verify that the grooves in the…
• 1990 Nissan Micra Manual Transmission Reassembly Procedure - Page MT-23
  This document is a single page (MT-23) from a manual transmission (transaxle) service manual section titled "REASSEMBLY." It gives a seven-step illustrated procedure for reassembling the transmission onto the clutch…
• Nissan Micra Manual Transaxle Mainshaft & Diff Side Bearing Preload - MT-22
  This is page MT-22 of a factory service manual covering the manual transaxle, specifically the mainshaft and differential side bearing preload adjustment procedure. It describes step 10 of a shim selection procedure…
• Nissan Micra Mainshaft & Diff Side Bearing Preload Adjustment - MT-21
  This is page MT-21 from a Nissan manual transmission service manual section covering mainshaft and differential side bearing preload adjustment. The page presents steps 7 through 9 of the procedure. Step 7 instructs…
• Nissan Micra Manual Transmission MT-19: Final Drive & Shift Control Inspection
  This page, MT-19, from a manual transmission (MT) service manual section titled 'Repair for Component Parts,' covers two topics. The left column continues the Final Drive assembly procedure: it instructs the technician…
• Nissan Manual Transmission Input Shaft Front Bearing Replacement - MT-11
  This is page MT-11 from a Nissan factory service manual, covering the manual transmission section titled "Repair for Component Parts: Input Shaft Front Bearing." It provides a four-step procedure for replacing the…
• 1990 Nissan Micra Manual Transaxle - Clutch Housing & Case Bearing Race Repair
  This page is from a factory service manual section titled "Repair for Component Parts," covering the Clutch Housing and Transmission Case (continued) of a manual transaxle. It describes servicing bearing outer races…
• Nissan Micra Manual Transmission Clutch Housing Oil Seal & Bearing Repair MT-9
  This is a single page from a factory service manual section titled 'Repair for Component Parts: Clutch Housing and Transmission Case' (page MT-9 of the Manual Transaxle/Transmission section). It illustrates seal and…
• Nissan Micra Manual Transaxle Disassembly Steps 6-10 - Final Drive & Shifter
  This is page MT-8 from a factory service manual, covering steps 6 through 10 of a manual transaxle disassembly procedure. Step 6 instructs raising both the input shaft and mainshaft just enough to remove and withdraw…
• Nissan Micra Manual Transaxle Disassembly (MT-7) - Case, Idler Gear, Retainer
  This document is page MT-7 from a Nissan factory service manual's Manual Transaxle (MT) section, covering the first five steps of transaxle disassembly. Step 1 instructs removal of bolts and plugs (including a labeled…
• Nissan Evaporative Emission Control Inspection - Fuel Check Valve & Relief Valve
  This is a scanned service manual page covering the Evaporative Emission Control System within the Exhaust Emission Control section (page EF & EC-34). It continues an inspection procedure for the carbon canister and…
• Nissan Throttle Opener Control System (TOCS) Adjustment & Vacuum Hose Color Code
  This is a scanned page (EF & EC-32) from a Nissan factory service manual section on Exhaust Emission Control, specifically the Throttle Opener Control System (T.O.C.S.). The left column continues an Inspection and…
• Nissan Micra T.O.C.S. Throttle Opener Adjustment - Emission Control EF & EC-30
  This is page EF & EC-30 from a Nissan service manual section on Exhaust Emission Control, specifically the Inspection and Adjustment procedure for the Throttle Opener Control System (T.O.C.S.). The page continues a…
• Nissan Throttle Opener Control System (T.O.C.S.) Inspection & Adjustment
  This service manual page covers inspection and adjustment of the Throttle Opener Control System (T.O.C.S.), part of the exhaust emission control system. It explains that when idle speed stays too high, the system…
• Nissan EGR Thermal Vacuum Valve (TVV) Inspection & Torque Spec - EF & EC-27
  This page is from a factory service manual section titled "Exhaust Emission Control: E.G.R. System, Inspection (Cont'd)" and covers inspection and replacement of the Thermal Vacuum Valve (T.V.V.). The procedure…
• Nissan EGR Control Valve Inspection & Vacuum Test - EF & EC-26 Service Manual
  This is page EF & EC-26 from a factory service manual section titled "Exhaust Emission Control: E.G.R. System, Inspection (Cont'd)." It continues an on-vehicle inspection procedure for the EGR system: the system is…
• Nissan Micra Idle Speed Control System Inspection - Solenoid Valve Test & Torque
  This is a scanned page (EF & EC-20) from a factory service manual covering inspection of the Idle Speed Control System. The procedure instructs the technician to verify that idle rpm increases 50 to 200 rpm when the…
• Nissan Micra Carburetor Dash Pot & Anti-Dieseling Solenoid Valve Adjustment
  This is page EF & EC-18 from a factory service manual's Engine Fuel & Emission Control (Carburetor) section, covering two inspection and adjustment procedures. The Dash Pot section gives a four-step procedure: warm the…
• Nissan Micra Carburetor Accelerating Pump Inspection & Adjustment - EF & EC-17
  This is a page from a factory service manual section covering carburetor inspection and adjustment (continued). Step 4 instructs the mechanic to install the carburetor on the engine and check engine speed after…
• Nissan Micra Carburetor Fast Idle & Auto-Choke Relay Check - EF & EC-16
  This is page EF & EC-16 from a Nissan service manual's Carburetor section, covering continued Inspection and Adjustment procedures. The left column completes the automatic choke heater circuit check: verifying…
• Nissan Micra Mechanical Fuel Pump Inspection Procedure - EF & EC-10
  This service manual page describes the bench inspection procedure for a mechanical fuel pump. It is a single page (EF & EC-10) from the Engine Fuel & Emission Control section of a factory service manual. The procedure…
• Nissan Micra Fuel Pump Static Pressure Test & Diagram - EF & EC-9
  This service manual page covers the mechanical fuel pump operating test for a carbureted Nissan engine (uploaded as applying to a 1990 Nissan Micra). It opens with a warning to disconnect the battery ground cable…
• Nissan Micra A.T.C. Air Cleaner Inspection - Vacuum Motor & Temp Sensor Test
  This is a page (EF & EC-7) from a Nissan factory service manual covering inspection of the Automatic Temperature Control (A.T.C.) air cleaner system on a carbureted engine. It explains that the viscous paper air…
• 1990 Nissan Micra Thermostat & Electric Cooling Fan Inspection - Wiring Diagram
  This is page LC-8 of a factory engine cooling system service section, covering thermostat and electric cooling fan inspection. The thermostat portion shows an exploded diagram of the water outlet, thermostat, and…
• Nissan Micra Water Pump Removal & Radiator Pressure Test - Cooling System LC-6
  This page is from a Nissan factory-style service manual section titled "ENGINE COOLING SYSTEM" (page LC-6), covering the water pump and radiator. The left column details water pump removal and installation precautions…
• Nissan Micra Oil Pressure Check & Oil Pump Removal - Service Manual Page LC-3
  This is page LC-3 from a Nissan factory service manual section titled "Engine Lubrication System," covering on-vehicle service (oil pressure check) and oil pump removal and installation. The oil pressure check…
• Nissan Micra Engine Overhaul - Main Bearing Torque & Crankshaft End Play (EM-27)
  This is page EM-27 from a Nissan engine overhaul service manual section, covering continued assembly procedures for the bottom end of the engine. It instructs the technician to tighten the main bearing cap bolts to the…
• Nissan Micra Engine Overhaul: Piston & Crankshaft Removal, Ring Clearance Specs
  This page (EM-21) from a Nissan factory service manual covers part of the Engine Overhaul section, split into Disassembly and Inspection columns. The Disassembly column describes mounting the engine on a work stand…
• Nissan Micra Engine Removal Diagram - Mount Torque Specs & Slingers (EM-19)
  This is a scanned page from a Nissan factory service manual covering the Engine Removal procedure, page EM-19 (illustration reference SEM924A). The page shows an exploded diagram of the engine and transaxle assembly…
• Nissan Micra Camshaft & Crankshaft Front Oil Seal Replacement - EM-18
  This is page EM-18 of a Nissan engine service manual (Engine Mechanical section) covering oil seal replacement procedures. The left column details replacement of the camshaft oil seal in six steps: remove the…
• Nissan Micra Cylinder Head Installation - Torque Sequence & Specs (EM-16)
  This is page EM-16 of a Nissan factory service manual covering the continuation of cylinder head installation. It instructs installing the cylinder head with a new gasket (always using a new gasket, verifying the oil…
• 1990 Nissan Micra Cylinder Head Assembly & Installation - Timing Marks (EM-15)
  This is page EM-15 from a factory service manual's Engine Mechanical section covering cylinder head assembly and installation. The assembly portion (continued) covers step 6, installing the rocker shaft with rocker…
• Nissan Micra Cylinder Head Inspection & Assembly - Valve & Camshaft Specs EM-14
  This is page EM-14 of a Nissan engine (EM) service manual section covering cylinder head inspection and assembly. The left column completes inspection procedures: valve dimensions must be checked against S.D.S…
• Nissan Micra Cylinder Head Inspection: Valve Inserts, Cam Journal & Runout Specs
  This page (EM-13) from a factory service manual covers cylinder head inspection procedures, continuing an 'Inspection (Cont'd)' section. It has two main topics. First, VALVE INSERTS: it instructs checking valve inserts…
• Nissan Micra Cylinder Head Valve Guide Replacement - Service Manual EM-12
  This is page EM-12 of a factory service manual engine mechanical (EM) section covering cylinder head valve guide replacement, continued from an inspection procedure. The page gives a four-step procedure: (1) heat the…
• Nissan Micra Cylinder Head Disassembly & Inspection - Warpage & Valve Guide Specs
  This is page EM-11 of a Nissan engine service manual covering cylinder head disassembly (continued) and inspection procedures. The disassembly section lists steps 4-7: remove the rocker shaft with rocker arms, remove…
• Nissan Micra Cylinder Head Removal & Disassembly - Bolt Sequence (EM-10)
  This is page EM-10 from a Nissan factory service manual covering cylinder head removal and disassembly procedures. The Removal section instructs: (1) remove the timing belt, cautioning that after removal the crankshaft…
• Nissan Micra Timing Belt Installation Procedure & Torque Specs (EM-8)
  This is page EM-8 of a factory service manual, covering the installation procedure for the engine timing belt. The procedure begins by confirming the No. 1 cylinder is at T.D.C. on its compression stroke, with a…
• 1990 Nissan Micra Timing Belt Removal Procedure - Service Manual Page EM-5
  This is page EM-5 of a factory service manual, covering the removal procedure for the engine timing belt. The page presents a nine-step procedure with supporting line illustrations. Steps include: jacking up the…
• Nissan Micra Rear Axle, Suspension Inspection & Brake Fluid Level Check - MA-23
  This page is from the Maintenance (MA) section of a Nissan factory service manual, page MA-23, titled "Chassis and Body Maintenance." It covers two inspection procedures. The first, "Checking Rear Axle and Rear…
• Nissan Micra Front Axle & Suspension Inspection - Service Manual Page MA-20
  This is page MA-20 from a Nissan factory service manual, in the Chassis and Body Maintenance (MA) section, covering the procedure "Checking Front Axle and Front Suspension Parts." The page instructs the technician to…
• Nissan Micra A/T Fluid Level Check, Condition & Change Procedure (MA-19)
  This is page MA-19 from the 'Chassis and Body Maintenance' section of a factory service manual, covering automatic transmission (A/T) fluid service. The 'Checking A/T Fluid Level' procedure explains that fluid can be…
• Nissan Micra Timing Belt Installation Procedure & Torque Specs - MA-14
  This is page MA-14 of a factory service manual section titled "Engine Maintenance: Before Engine Starts (Cont'd)", covering timing belt installation. The procedure instructs: confirming No. 1 cylinder is at TDC on the…
• Nissan Micra Spark Plug Specs, Ignition Wire & A.T.C. Air Cleaner Check MA-12
  This is page MA-12 from a factory service manual, in the Engine Maintenance section under 'Before Engine Starts (Cont'd)'. It lists spark plug specifications for Canada: standard type BPR5ES, hot type BPR4ES, and cold…
• Nissan Micra Engine Maintenance MA-9: PCV Filter, Fuel Filter & Coolant Change
  This is a scanned page (MA-9) from a factory service manual's Engine Maintenance section, under the heading "Before Engine Starts (Cont'd)." It covers five maintenance procedures. Replacing the P.C.V. filter requires…
• Nissan Micra Service Manual MA-5: General Maintenance Inspection Checklist
  This is page MA-5 of a factory service manual's Maintenance (MA) section, titled "General Maintenance." It presents a two-column table listing interior and driver-control inspection items with cross-references to…
• 1990 Nissan Micra Service Manual: General Precautions Page GI-3
  This is page GI-3 of a factory service manual's General Information "Precautions" section, uploaded as part of a 1990 Nissan Micra document set. The page lists general service precautions numbered 7 through 17…
• Nissan Micra Instrument & Back Door Harness Layout Diagram - EL-64 Wiring
  This is page EL-64 from a Nissan factory service manual electrical section, titled "HARNESS LAYOUT." It contains two illustrated harness routing diagrams. The first, "Instrument Harness" (figure SEL527I), shows the…
• Nissan Micra Main Harness Layout - Passenger Compartment Connectors (EL-63)
  This is page EL-63 from a Nissan factory service manual electrical section, showing the 'Harness Layout: Main Harness (Cont'd)' for the passenger compartment. A large perspective line drawing depicts the vehicle body…
• Nissan Micra Battery Test & Charging Chart (Chart I) - Service Manual EL-10
  This page is from a Nissan service manual (page EL-10, Electrical section) covering the battery. It presents "Chart I" of the M.F. (maintenance-free) Battery Test and Charging Chart, a flowchart guiding technicians…
• Nissan Micra Clutch Cover Installation - Alignment Tool KV30101200 (CL-6)
  This is page CL-6 from a Nissan factory service manual, part of the Clutch (CL) section, covering the procedure 'Installing Clutch Cover (Cont'd)'. The page contains one instruction: insert the special tool into the…
• Nissan Micra Service Manual MA-31: Lock/Hinge Lubrication & Seat Belt Checks
  This is page MA-31 from a Nissan service manual, covering "Chassis and Body Maintenance: Body." The page presents two maintenance procedures. The first section, "Lubricating Locks, Hinges and Hood Latches," uses…
• Nissan Idle Speed & CO% Adjustment After Warm-up - Service Manual Page MA-17
  This page, MA-17 from a factory service manual's Engine Maintenance section titled "After Engine Warm-up (Cont'd)", presents a flowchart procedure for checking and adjusting idle CO percentage and idle speed after…
• Nissan Micra Lubrication Chart - Maintenance Intervals & Fluid Service (MA-7)
  This is a scanned page (MA-7) from a Nissan factory service manual showing the Lubrication Chart for a front-wheel-drive vehicle, uploaded to a 1990 Nissan Micra gallery. The chart uses a vehicle chassis diagram with…
• 1990 Nissan Micra Towing Points Diagram - Front & Rear Tow Hooks (GI-16)
  This is page GI-16 from a Nissan factory service manual, in the General Information (GI) section, covering 'Lifting Points and Tow Truck Towing', specifically the continuation of the 'Tow Truck Towing' subsection. The…
• Nissan Micra Lifting Points & 2-Pole Lift Diagram - Tow Truck Towing (GI-14)
  This service manual page, GI-14 from the General Information (GI) section, covers 'Lifting Points and Tow Truck Towing' with focus on 2-pole lift procedures. It begins with a warning: when lifting the vehicle, the lift…
• Nissan Micra Lifting Points & Jacking Positions - Jack, Safety Stand, Tow Hooks
  This page, GI-13 from a Nissan service manual's General Information section, covers "Lifting Points and Tow Truck Towing." It begins with two safety warnings: never get under a vehicle supported only by a jack (always…
• Service manual page EL-56: locating a broken defogger filament and repairing it with Dupont No. 4817 conductive silver and a heat gun.
• Service manual page EL-33: ignition trouble-shooting tests 5 to 8 with voltmeter and ohmmeter hookups, 11.5-12.5 volt results and actions.
• Service manual page EL-32: ignition trouble-shooting tests 1 to 4 with meter hookups, conditions, results and actions.
• Service manual page EL-26: alternator slip ring tests (32.4 mm min. diameter) and brush checks with 7 mm wear limit and 3.040-4.217 N spring pressure.
• Service manual page EL-21: starter reassembly with grease points, 0.1 to 0.5 mm end play (A/T) and 0.3 to 2.5 mm pinion clearance "ℓ".
• Service manual page EL-18: starter magnetic switch continuity tests, plunger check and pinion/clutch check for M2T37081 (M/T) and M2T23685 (A/T).
• Service manual page EL-13: standard charge flowchart, Fig. 4 initial charging current setting, Fig. 5 additional charge times and cautions.
• Service manual page EL-12: slow charge flowchart, Fig. 2 initial charging current by battery type, Fig. 3 additional charge times and cautions.
• Service manual page EL-11: M.F. battery capacity test flowchart, Fig. 1 discharging current by battery type, and the 9.6 volt load test threshold.
• Service manual page EL-9: hydrometer and thermal gauge reading plus a chart converting electrolyte specific gravity to 20°C (68°F).
• Page BF-19: leave original sealant and primer on unbroken glass when removing it; repair leaks with primer E and sealant worked in with a flat stick.
• Page BF-18: apply primer E and a 10 (0.39) mm sealant bead, install glass within 15 minutes; sealant drying times by temperature and humidity.
• Page BF-17 back door glass replacement: cutting sealant, cleaning bonding surfaces, spacer placement at 100 (3.94) mm and applying primer A.
• Page BF-15: roof side molding, door molding, side guard molding heated to 30 to 40°C (86 to 104°F), door weatherstrip and door corner finisher.
• Page ST-7 R22T gear: tie-rod outer ball joint swinging force 2.26 - 68.65 N, inner ball joint 1.18 - 60.80 N.
• Page ST-5 steering column: length L 573.2 - 574.8 mm non-tilt, 563.2 - 564.8 mm tilt; snap ring rounded face toward bearing.
• Page BR-6 brake pedal adjustment: free height H 190 - 200 mm manual, 194 - 204 mm automatic transaxle, depressed height 95 mm, clearance C 0.3 - 1.
• Page FA-10 drive shaft assembly: 60 - 90 g (2.12 - 3.17 oz) grease per joint, boot length L 85.5 mm wheel side and 82.5 mm transaxle side.
• Page FA-6: press outside grease seal and bearing, select spacer by mark or by L = L1 - L2 (L2: 1.19 mm), tighten wheel bearing lock nut.
• Service manual page FA-5: wheel hub and knuckle inspection, then greasing bearings, pressing outer races and installing the inner race and grease seal.
• Service manual page FA-4: removing the right and left drive shafts and bearing lock nut, then pulling the outer wheel bearing and knuckle bearing outer races.
• Service manual page AT-64: causes of low or high line pressure, throttle wire check, and the lock-up pressure test with a gauge at port 4 in D range.
• Service manual page AT-63: pressure test port locations, line pressure at idle and stall in R, D, 2 and 1 at 43-57°C ATF, and low line pressure diagnosis.
• Service manual page AT-56: road testing upshift, downshift, lock-up and kickdown speeds in D, plus 2 and 1 range checks, with a throttle position drawing.
• Service manual page AT-55: governor cap and fluid leak checks, ATF color and odor diagnosis, and road testing in the P, R, N and D ranges.
• Service manual page AT-53: manual shaft nuts at 16-22 N·m, control valve body, oil pan with two magnets, governor cap snap retainer, oil pump and input shafts.
• Service manual page AT-46: band servo piston install and air check, high-reverse clutch (front), forward clutch (rear) and front carrier with internal gear.
• Service manual page AT-45: installing the oil pump, low and reverse brake piston and retainer (7-9 N·m), parking pawl, return spring, shaft and brake band.
• Service manual page AT-43: diff side bearing preload Type B measured with KV38105900, specified 2.9-4.4 N·m (30-45 kg-cm, 26-39 in-lb), shims per S.D.S.
• Service manual page AT-37: pressing races onto the idler gear and output shaft, then bearing retainer, inner race, oil seal and O-ring removal.
• Service manual page AT-36: planetary carrier clearance 0.20-0.70 mm, replace over 0.80 mm; output shaft and idler gear race removal with ST22730000 (J25681).
• Service manual page AT-31: high-reverse clutch (front) clearance, standard 1.0-1.4 mm, limit 2.2 mm, plus air testing and 31537-01X00 to X04 retainer plates.
• Page AT-30: lubricating the drum bushing, piston seal direction, refitting springs and retainer with snap ring, and installing driven and drive plates.
• Page AT-28: reamer bolts, strainer bolts 45, 50, 57 and 65 mm, adjusting screw backed off 6 and a half turns, lock nut 3.4 - 4.4 N·m (2.5 - 3.3 ft-lb).
• Page AT-24 oil pump assembly: gear hub, relief spring and steel ball, pump plate flush with housing, and seal ring A (white) and B (no mark) locations.
• Page AT-23 oil pump checks: gear to housing 0.02 - 0.04 mm, seal ring 0.10 - 0.25 mm, and gears 31346-01X00 to X03 and 31347-01X00 to X03.
• Page AT-21 disassembly: lifting out the oil pump assembly, removing the inhibitor switch, band servo piston and band brake servo with return springs.
• Page AT-20: securing the flexible brake band with a 2 mm (0.08 in) wire clip, pulling the parking pawl shaft and removing the low and reverse brake piston.
• Page AT-17 disassembly: manual shaft nuts, retaining pin and throttle lever, parking actuator support, band brake piston stem, accumulator piston, final drive.
• Page AT-13 final installation checks: adjust control cable, test inhibitor switch, check fluid, verify shifts, line pressure test and stall test.
• Page AT-11: inhibitor switch set at N with a 2.5 mm (0.098 in) pin, and diff side oil seal removal with ST33290001 and install with ST33400001.
• Page AT-9 control cable adjustment from P to 1 range, setting nuts A and B at the trunnion and checking spring pin orientation on the manual lever.
• Page AT-8 throttle wire removal and adjustment at nuts A and B, nut A 5 - 7 N·m (0.5 - 0.7 kg-m, 3.6 - 5.1 ft-lb), and the effect on kickdown.
• Page AT-7: checking ATF on the dipstick at HOT 50-80°C (122-176°F) or COLD 30-50°C (86-122°F), and removing the control valve assembly.
• Bearing inspection and synchronizer assembly; groove clearance 0 - 0.15 mm (0 - 0.0059 in), 1st & 2nd hub snap rings 2.0 mm and 2.1 mm thick.
• Removing thrust washer, 2nd gear and front bearing race; baulk ring to gear clearance standard 1.0 - 1.35 mm, wear limit less than 0.7 mm (0.028 in).
• Mainshaft disassembly with standard gear end play, 1st 0.22 - 0.44 mm through 5th 0.22 - 0.29 mm, and removal of 5th, 4th and 3rd gear parts.
• On-vehicle service steps for pulling and driving the differential side oil seal and removing the shift control oil seal with a pin punch.
• RS5F41A transaxle takes 2.6 liters (5-1/2 US pt, 4-5/8 Imp pt) of gear oil; speedometer pinion 10 mm (0.39 in) and select stopper adjustment.
• Pedal height "H" 198 - 208 mm (7.80 - 8.19 in), withdrawal lever play "B" 2.5 - 3.5 mm, free play "A" 12.5 - 17.5 mm; stopper lock nut 16 - 22 N·m.
• Accelerator wire service: pedal free play 1 - 3 mm (0.04 - 0.12 in) and double nut "A"/"B" adjustment with throttle drum at full close.
• Float stopper "h": 46.5 - 47.5 mm (1.831 - 1.870 in), choke index mark alignment and bimetal cover screws 1.5 - 3.9 N·m (1.1 - 2.9 ft-lb).
• Carburetor service page covering removal precautions, cleaning, sight glass fuel level check and float level "H": 16.5 - 17.5 mm (0.650 - 0.689 in).
• Idle compensator page: No.1 opens 60-70°C (140-158°F), No.2 70-80°C (158-176°F), with breath leak test and warm-air operating check.
• Service manual page EM-26: main bearing grade selection table, piston ring orientation, piston grade and ring set marks, main bearing cap sealant.
• Service manual page EM-25: piston pin press tool KV10109900, upper and lower main bearing positions, block and crankshaft journal grade numbers.
• Service manual page EM-24: piston clearance 0.023-0.043 mm, 0.04 mm feeler extracting force 4.9-14.7 N, flywheel runout under 0.15 mm (0.0059 in).
• Service manual page EM-23: crankshaft runout under 0.08 mm, block warpage under 0.1 mm, cylinder bore 71.00-71.03 mm (2.7953-2.7965 in).
• Service manual page EM-22: piston ring gap, main bearing clearance 0.03-0.05 mm, rod bearing 0.02-0.06 mm, crankshaft out-of-round and taper checks.
• Service manual page EM-17: oil pan removal with seal cutter KV10111100, oil pump torque 16-22 N·m (12-16 ft-lb), liquid gasket bead 3.5-4.5 mm.
• Service manual page EM-7: timing belt worn side surface, worn teeth and oil or coolant contamination, with causes such as belt tension and seal leaks.
• Timing belt inspection chart: broken belt, broken or cracked tooth and cracked or worn back surface, each with drawings and likely causes.
• Service manual page EM-3: compression test steps, standard 1,245 kPa (12.7, 181)/350, minimum 981 (10.0, 142)/350, max difference 98 (1.0, 14)/350.
• Service manual page MA-30: static vs dynamic wheel balancing, P155/80 D12 spare tire at 35 psi (240 kPa) and 80 km/h (50 MPH) max, steering linkage checks.
• Service manual page MA-29: wheel nut types, torque 98-118 N·m (10.0-12.0 kg-m, 72-87 ft-lb), 40 psi (275 kPa) bead seat limit and rim runout limits.
• Service manual page MA-28: tire replacement cautions, criss-cross wheel nut tightening and aluminum wheel nut install steps, recheck after 1,000 km (600 miles).
• Service manual page MA-27: abnormal tire wear chart (shoulder, center, toe-in or toe-out, uneven) with causes and fixes, plus 4-wheel radial rotation.
• Service manual page MA-26: parking brake pulling force 196 N (20 kg, 44 lb) at 7-9 notches, lever stroke adjustment, tire condition and inflation.
• Service manual page MA-25: lining wear limit 1.5 mm (0.059 in), drum repair limit 181.0 mm (7.13 in), pedal free height M/T 190-200 mm, A/T 194-204 mm.
• Service manual page MA-24: brake booster function and brake line checks, rotor repair limit 11.0 mm (0.433 in) and pad wear limit 2.0 mm (0.079 in).
• Service manual page MA-22: toe-in 2-4 mm (0.08-0.16 in), side rod "L" 107.1 mm (4.22 in) and turning angles 40°30'-43°30' inside, 32°30'-35°30' outside.
• Chassis and body maintenance page MA-21: wheel bearing axial play 0 mm, drive shaft boot check, camber -25' to 1°05', caster 1°30' - 3°00' and toe-in setup.
• Chassis and body maintenance page MA-18: exhaust check, clutch pedal free height 198 - 208 mm, M/T oil level check and RS5F41A oil capacity 2.6 liters.
• Engine maintenance page MA-16: flowchart for checking ignition timing and idle speed, M/T 750 rpm and A/T 700 rpm (in D), with distributor adjustment.
• Engine maintenance page MA-15: valve clearance intake 0.25 mm (0.010 in), exhaust 0.30 mm (0.012 in), lock nut 11 - 15 N·m, and idle and timing preparation.
• Timing belt removal, page MA-13: jack up, remove engine mounting, set No. 1 cylinder at T.D.C. on the camshaft pulley mark and release the tensioner.
• Engine maintenance page MA-11: oil refill 2.8 L with filter, 2.6 L without, and spark plug replacement with a 0.8 - 0.9 mm (0.031 - 0.035 in) gap.
• Engine maintenance page MA-10: cooling system flush with coolant capacity 4.3 L without heater, 4.7 L with heater, and engine oil and filter change steps.
• Engine maintenance page MA-8 covering drive belt deflection and alternator belt adjustment, air cleaner filter replacement and choke mechanism check.
• Service manual page EL-41: headlamp aiming adjustment at 7,620 mm (300.00 in) and bulb specs including H6054 sealed beam and 1156 bulbs.
• Service manual page EL-14: quick charge flowchart, Fig. 6 charging current and time, cautions, and S.D.S. for the 46B24L-MF 12-45 V-AH battery.
• Page BR-13 LT18B rear drum: standard inner diameter 180.0 mm (7.09 in), maximum 181.0 mm (7.13 in), out-of-roundness less than 0.03 mm.
• Page BR-11 CL16 rotor inspection: maximum runout less than 0.07 mm (0.0028 in), minimum thickness more than 11.0 mm (0.433 in).
• Service manual page AT-35: governor disassembly and inspection with spring chart, primary governor 31.7 mm (1.248 in), secondary 38.2 mm (1.504 in) free length.
• Clutch disc runout 0.7 mm (0.028 in), rivet head wear limit 0.3 mm, diaphragm spring height "A" 27 - 29 mm, uneven limit 0.5 mm, tool ST20050240.
• Oil pump inspection: rotor tip and side clearance less than 0.2 mm (0.008 in), outer rotor to body less than 0.25 mm (0.0098 in).